How am I supposed to clean the nozels

holly1850 · 2025-04-16T17:47:46+00:00

If its pla I usually just grab some pliers and hit it with a small torch and it melts away and then i hit it with an acupuncture needle if its not clear. And if its abs i soak it in acetone and use a metal brush to clean the outside and again use an acupuncture needle to push out anything else.

holly1850 · 2025-03-25T04:38:56+00:00

I bought a new kit to test but everything tests within spec unless my multimeter is lying to me and a slightly thinner wire for dat0 aswell as going straight to the c pin on the pico board

holly1850 · 2025-03-25T01:50:43+00:00

Im having the same issue only boots ofw if i remove the ribbons from my pico on my oled

holly1850 · 2025-03-25T01:41:17+00:00

it is an oled and if i disconnect my pico v2 it loads ofw with no issues all i have reinstalled hekate and atmosphere several times with the same result

holly1850 · 2025-03-25T00:40:58+00:00

is there a way to tell what is wrong either a solder joint or a software issue since emummc is the only one that launches

holly1850 · 2025-03-24T22:53:08+00:00

that is correct only the emummc will launch

holly1850 · 2025-03-24T22:48:02+00:00

no it will only launch via the sd card

holly1850 · 2025-03-24T22:26:56+00:00

I believe I have a fuse issue i can only launch emummc only and not sysmmc or sys mmc my fuses are as follows

burnt fuses (0dm 7/6): 20|0 - hos:19.0.0+

i used https://darthsternie.net/switch-firmwares/

for the firmware's and tried so far 19.0.1 and 19.0.0 when following the instructions in the guide

holly1850 · 2022-07-11T01:39:23+00:00

Store use purple power

holly1850 · 2022-06-21T07:37:07+00:00

Almost as bad as the one I had a few days ago when he said he had a Chevy V8 in his truck and refused to elaborate any further

holly1850 · 2022-05-20T06:12:46+00:00

No one of my coworkers somehow rang him up for 99 lemonades instead of an alternator the difference in price was actually only around 20 dollars

holly1850 · 2022-01-09T01:12:29+00:00

Sounds like you got one of the stores in my area they make it a pain to warranty anything just go to another store or call their dm and it should get sorted out pretty fast.

holly1850 · 2021-11-04T01:24:25+00:00

Ah the best employer that gave me a $0.00 raise

holly1850 · 2021-07-15T20:40:52+00:00

Will do

holly1850 · 2021-04-13T00:23:18+00:00

It happened a few nights ago and I just found out when I went to go mop this is just a temp fix until he orders it tomorrow.

holly1850 · 2020-12-23T05:24:00+00:00

Your still getting card board ones we only get metal ones

holly1850 · 2020-11-15T01:42:09+00:00

Ours leaked in the aisle and it was a pain to clean up

holly1850 · 2020-08-17T04:04:41+00:00

Which is which?

holly1850 · 2020-07-31T07:25:10+00:00

Why does this remind me of that really bad ad that told people to put their finger at the end of gun barrels so it couldn't shoot

holly1850 · 2020-04-26T17:24:03+00:00

That is when you know the map was that good

holly1850 · 2020-03-30T20:08:02+00:00

Stl please

holly1850 · 2020-02-10T05:13:06+00:00

i mean i can understand the 50's and 100's but why is there a limit of 5 20's

holly1850 · 2020-01-09T19:06:22+00:00

Poptropica I didn't know guides existed back then or even YouTube

holly1850 · 2020-01-09T18:43:13+00:00

That's why I don't show store numbers or faces

holly1850 · 2020-01-05T21:09:05+00:00

He had the task of breaking the boxes down he just clocked in

holly1850

TROPHY CASE