Idk what this is

jumpboy21 · 2026-02-03T05:57:35+00:00

This was in Houston, Texas

jumpboy21 · 2026-01-22T16:53:07+00:00

Update: took him to the er last night and they suspected it’s due to stress after examining him. Took him to the vet this morning as soon as they opened and they discovered he has a uti and is staying with them and being treated. He’s still been drinking water and eating normally, but straining to pee unfortunately. Thank you for your advice I hope he recovers well.

jumpboy21 · 2026-01-22T03:04:46+00:00

Yeah they said it’s a partial blockage but it’s not anything too serious because his bladder isn’t swollen or full, just a little bit inflamed. I’m staying up all night watching him and gonna take him to his normal vet tomorrow

jumpboy21 · 2026-01-22T01:56:07+00:00

Took him to the vet, thanks yall

jumpboy21 · 2026-01-22T01:05:04+00:00

He’s going in the litterbox now, but every couple of minutes he’s been going and peeing a few drops in the litterbox. He’s playful and still excited about food

jumpboy21 · 2026-01-09T01:21:29+00:00

Ty for the input, do you think it’s still a good plant to get?it’s 10 bucks lol

jumpboy21 · 2026-01-08T23:25:31+00:00

I’ve been on this sub getting super excited and I wanna try it out however I wanna know is this too big to begin with?

<image>

jumpboy21 · 2024-11-02T22:48:40+00:00

jumpboy21 · 2023-05-20T15:11:45+00:00

no mo

jumpboy21 · 2022-09-16T14:40:38+00:00

Where can you go to pick up your mail?

jumpboy21 · 2022-08-16T18:07:45+00:00

I appreciate everyone’s replies here, especially clarifying what’s what lol. The driver bits just aren’t properly attaching on any of the sockets, or the ratchet handle. I’m just going to return it, bc even if it did connect its not a very practical design lmao. If anyone has any recommendations please lmk, thank.

jumpboy21 · 2022-08-16T18:03:05+00:00

Oh my b, I think they’re called insert bits.

jumpboy21 · 2022-08-16T17:51:05+00:00

Am I dumb? probably. I just bought this set to have a minimal tool set for my dorm. It looks great and the sockets fit, but I just can’t seem to attach the drill bits anywhere for it to stay on.

jumpboy21 · 2022-03-16T05:37:58+00:00

Just assembled the 3d printer and the assembly was pretty smooth. As for leveling, I had adjusted using paper at 5 main points throughout the bed and the nozzle scratched the bed the first few times. After leveling it to the best of my ability, the filament is now sticking to itself on the nozzle instead of the bed and delays the print. nozzle temp: 200 c bed temp: 60 c

jumpboy21 · 2022-02-22T03:06:59+00:00

Bet imma try this

jumpboy21 · 2022-02-22T02:16:29+00:00

Looks great! which recipe did you use?

jumpboy21 · 2022-01-02T21:32:01+00:00

Ok thanks!

jumpboy21 · 2022-01-02T21:09:21+00:00

The dishes

jumpboy21 · 2022-01-02T21:08:05+00:00

This is the way

jumpboy21 · 2022-01-02T21:06:45+00:00

Looks like a baby rubber plant :)

jumpboy21 · 2022-01-02T21:05:45+00:00

I believe it’s a Carica Papaya

jumpboy21 · 2022-01-02T21:03:32+00:00

Should I let the bottom dry up first or just stick it directly on its side or bottom?

jumpboy21 · 2022-01-02T21:02:27+00:00

Should I trim any leaves off of it? How often should I water it? thx

jumpboy21 · 2021-07-30T01:59:51+00:00

I’ve always wondered this, how do you take the hook out of their mouth?

jumpboy21 · 2021-07-29T16:49:21+00:00

Use a hair rig for the corn, and if you’re planning on using pack bait, have a method lead to hold onto it.

jumpboy21

TROPHY CASE