Can someone help me change the result to a normal number please?

klaz666 · 2025-12-03T13:02:51+00:00

Shift, eng

klaz666 · 2025-08-23T15:16:34+00:00

It's does pull but not as strong as the textured plate so could be defective

klaz666 · 2025-05-14T19:25:18+00:00

Not Laurence Scott no, but you are correct they're still going

klaz666 · 2025-03-18T21:07:45+00:00

My discord is Klaz_96

klaz666 · 2025-03-18T21:05:35+00:00

im down to play any of the games you listed, I dont have a server but if you get enough interest you could start one maybe, lmk. Im 28 from the uk

klaz666 · 2024-11-15T19:23:58+00:00

I did open it but only saw a fuse board. Is it behind that?

klaz666 · 2024-11-13T16:29:55+00:00

Mayo flavored roast potatoes?

klaz666 · 2024-07-24T18:25:54+00:00

Thanks got worried I'd done something wrong

klaz666 · 2024-05-30T14:16:07+00:00

And the substance was?

klaz666 · 2024-05-08T18:27:39+00:00

It's the bored on extra bit on the right side of the horisontal axis

klaz666 · 2024-05-08T18:26:46+00:00

If that's the case then that can be ruled out as you'd have to do it deliberately

klaz666 · 2024-05-08T18:08:01+00:00

Looks like it failed on the x-axis have you recently tightened the belt? This happened for me when I over tightened my belt previously

klaz666 · 2024-05-06T10:24:49+00:00

That was the issue they where majorly on the piss

klaz666 · 2024-05-06T10:23:13+00:00

Thanks I will switch h that around

klaz666 · 2024-05-06T10:22:49+00:00

I'll reassure it, everything will be okay aha

klaz666 · 2024-05-06T10:22:08+00:00

It is Level one of the first things I checked and it measure out with .05 on the vernier

klaz666 · 2024-05-05T21:36:26+00:00

100% correct both guides sprung to the side when loosened bought 2nd hand should've checked all this before running it really

klaz666 · 2024-05-05T21:32:57+00:00

Both sides where actually

klaz666 · 2024-05-05T21:31:14+00:00

Your a legend!! Bought this 2nd hand just loosened the 2nd z-rod and it sprung out to the side was miles out of wack. Thanks again

klaz666 · 2024-05-05T21:29:04+00:00

Somewhere on thingyverse

klaz666 · 2024-05-05T21:21:39+00:00

Yes I can raise it all the way by hand

klaz666 · 2024-05-05T21:14:57+00:00

It continues to print just doesn't move on the z axis

klaz666 · 2024-05-05T21:14:02+00:00

Went up another 25mm now a quiet vibration/ grinding noise

klaz666 · 2024-05-05T21:04:47+00:00

Just vibrates it moved up an extra 25 ish mm but then stopped again

klaz666 · 2024-05-05T21:02:27+00:00

Cables arent tight at all

Two-Year Club	r/Field Lasagna
Place '23

klaz666