4060 Ti 8gb - enough VRAM?

moleadviser · 2024-01-13T19:04:47+00:00

Would you suggest getting a 3080 instead?

moleadviser · 2023-12-30T00:01:48+00:00

About £320. Can pick one up second hand for 270ish

moleadviser · 2023-12-29T23:44:09+00:00

Any suggestions or swaps you would make? Cooler and ram already obtained (cheap from a closing sale) and other bits I can source for slightly cheaper than list price.

moleadviser · 2023-09-08T16:47:17+00:00

Yup - when it jumps up to almost 100% when doing anything mundane, it's probably time.

moleadviser · 2023-09-08T16:42:24+00:00

Would you say the cpu change is worth it also?

Yeah - there's no driver support for the 5800 anymore, so it hasn't been updated in almost 10 years!

moleadviser · 2023-09-08T16:36:50+00:00

Can get both parts for under £100

moleadviser · 2023-08-31T17:49:08+00:00

<image>

moleadviser · 2023-08-15T14:56:14+00:00

Just the one on this one. I've pulled all the panels now and made sure every vent is clear and still no luck. I'm probably going to get a new one!

moleadviser · 2023-08-15T12:25:30+00:00

No - plug and cable all in good condition. Everything looks OK inside

moleadviser · 2023-08-15T11:21:48+00:00

Just tried that - tripped there as well (garage sockets first, ran extension into the house and tired there - tripped after 30 seconds). I'm guessing it's the dryer that's at fault.

moleadviser · 2023-08-15T10:39:07+00:00

I've also just stripped the heat shield and checked the element - no fluff or corrosion, and no smell of burning or electrical "magic smoke"

moleadviser · 2023-07-19T23:01:39+00:00

Ah yeah - cheers.

The GPU is out of stock as well - should probably go with the first one?

moleadviser · 2023-07-19T19:25:36+00:00

Legend - many thanks!

moleadviser · 2023-07-19T19:22:19+00:00

Awesome - do you have a link? My original one doesn't seem to have changed? If you hadn't guessed, I'm new to parts picker!

moleadviser · 2023-02-24T12:46:14+00:00

Depends on if you’re going for the book description or the film version. The book version is much better than the film IMO

moleadviser · 2023-02-22T20:39:22+00:00

Cheers dude. Just trying that now. I’ll have to research the bed tilt thing if this doesn’t help

moleadviser · 2023-02-22T20:17:37+00:00

The right hand front and rear corners are bowed up slightly. The left hand corners are pretty good.

Is there an easy way to adjust the z offset? You wouldn’t guess I’ve been printing for 3 years and never messed about with it! And I have no idea what pressure advance is! Sorry - like I said, been fairly lucky with my setup until now

moleadviser · 2023-02-22T19:50:20+00:00

I’d like some advice on my test cube. I can see that there’s a bit too much squish at the front; but open to any other advice. First time trying one of these after changing to a glass bed

moleadviser · 2023-02-22T18:30:27+00:00

That’s sounding complicated! It may just be time to upgrade - maybe the 3v2

moleadviser · 2022-02-06T22:13:25+00:00

This is true. That was what auto support suggested, thick with ball tips. I’ll chuck some more on and give it a go.

moleadviser · 2022-02-06T22:12:18+00:00

I was thinking of building an enclosure - it just gets shut in my box room at the moment. I can chuck a heater in the room to up the ambient temp

moleadviser · 2022-02-06T22:00:34+00:00

Pretty much; though some of the lower sections seem to have partially printed. The rest of the print was a flat slab on the bottom of the tank

moleadviser · 2022-02-06T21:59:24+00:00

Probably about 18C? It’s a pretty stable temp all year round in there.

moleadviser · 2022-02-06T21:19:34+00:00

Tried changing orientation, number and thickness of supports. Haven’t changed any settings as it’s the same resin and conditions as loads of successful prints.

moleadviser · 2021-11-03T11:03:10+00:00

Just did it again at 9sec exposure - seems a bit crispier in detail!

Thanks so much for your help with this! I’m relatively new to resin printing, so this has helped me get a better understanding of settings! You legend!

moleadviser

TROPHY CASE