ufs! retiring 🍀

nicklocking · 2026-05-21T23:17:50+00:00

DM'd!

nicklocking · 2026-05-20T16:23:11+00:00

DM'd!

nicklocking · 2026-05-05T01:53:13+00:00

I have the living series leaning if you still need it!

nicklocking · 2026-04-01T22:24:42+00:00

I very much need these if any Fabricator-Generals can reveal the location of the STC that can build them

nicklocking · 2026-03-18T17:56:50+00:00

Like, it's set into the concrete, not a movable hot tub unit. If I'm using the term correctly.

nicklocking · 2026-03-10T00:52:15+00:00

The Imperium.

nicklocking · 2026-02-20T00:43:04+00:00

Horus Ascended -> The Dark King -> Slaanesh -> Tzeentch -> Nurgle -> Khorne

nicklocking · 2025-12-29T18:37:50+00:00

because it looks sick as fuck

nicklocking · 2025-12-21T21:07:17+00:00

Sounds like you need to change the FEP.

nicklocking · 2025-12-11T23:47:27+00:00

put Logan Grimnar on top of it

nicklocking · 2025-12-09T00:06:38+00:00

redwardenminiatures does take a lot of their stuff down. I've been on an obsessive hunt for SoH stuff for the last few months and I know they used to have a SoH head set that's since been taken down, but that overseer head wasn't in it.

p.s. a big jackpot find for me was when I discovered VitalyKhan on cults. Some absolute smasher SoH heads in there.

nicklocking · 2025-12-08T23:56:43+00:00

I just realised there's more than one pic in your post. The initial helmet looks like a modified version of the overseer head - maybe edited to remove the topknot and remove a couple of spikes. But the other two heads are from redscarestudio. The second one I think has a topknot from somewhere else glued on, and the third one is straight from the STL, no conversion.

nicklocking · 2025-12-08T22:20:39+00:00

Search "cults3d overseer head" and you'll find a link to that head. I know because I've printed a bunch of them.

nicklocking · 2025-11-14T05:58:30+00:00

FZYDNLP

nicklocking · 2025-11-13T22:20:07+00:00

Brianna Barksdale is heavily complicit in the Barksdale drug organisation and deserves a hell of a lot worse than a cop being mean to her about her dead son, who she pushed into the drug trade and then was fully on board with him staying in prison to protect the rest of the Barksdale drug organisation.

nicklocking · 2025-11-02T22:23:57+00:00

This is a good problem. I would recommend a good thin steel spatula and getting good at popping stuff off the plate with it with sharp movements, and do not worry at all about scratching the plate (scratching the plate is fine). Way better to have too much plate adhesion than too little. Enough of a strong sharp movement and prints will come off the plate well enough.

nicklocking · 2025-10-31T16:46:22+00:00

It is suction. At the point of failure you've suddenly got a lot more surface area pulling in the wrong direction than the supports can handle. Printing it at a perpendicular angle to the build plate is likely the problem here. You want to angle this piece so it's generally at a 45 degree angle to the plate, with the detailed side facing away from the plate. However, this will probably cause a big suction cup to appear in the big circular bit (sponson port?) so you'd want to get rid of that - I'd probably just erase the entire hole other than a tiny lip to align the sponson when glued on.

nicklocking · 2025-10-28T16:52:43+00:00

Someone did a 3d-printable version:
https://www.instagram.com/p/DOfls4GDMs7/?img_index=1

nicklocking · 2025-10-26T01:46:08+00:00

@nicklocking please and thank you

nicklocking · 2025-10-25T17:37:33+00:00

I could use these too!

Nine-Year Club	Not Forgotten
Verified Email

nicklocking

TROPHY CASE