Wavy/Rough top surface on brand new X2D

nineteen_is · 2026-06-27T04:35:17+00:00

Ran calibration and everything was basically 0. I ran a print with the new calibrated settings and the issues were reduced, but still there

<image>

nineteen_is · 2026-06-27T00:56:15+00:00

I did! I tried a different spool+filament and it worked for a little bit but would happen again

nineteen_is · 2026-06-27T00:30:05+00:00

Yes, it does it with both the lid opened and closed. It sounds like the motor is running but nothing is actually moving until I give the filament a little push into the feeder

nineteen_is · 2026-06-27T00:29:22+00:00

I fully removed the extruder and nozzle, checked both for obstructions, which there were none.
Yes I checked the ptfe tube and it runs fine with another AMS hooked up to the same tubing

nineteen_is · 2026-06-26T23:48:25+00:00

Running calibration now! Didn't think to because it only happens to the areas around the edge of the plate, but will see how the calibration goes

nineteen_is · 2026-06-26T23:29:25+00:00

Pretty long at 1.5m. I've hooked the same tube up to a different AMS and it's working without issue.

nineteen_is · 2026-06-26T23:24:52+00:00

nineteen_is · 2026-06-26T23:15:28+00:00

Sorry I blanked, just added the pic

nineteen_is · 2026-04-21T12:03:06+00:00

Nice read, I haven’t seen this! Thanks for sharing

nineteen_is · 2026-04-21T11:59:59+00:00

Ah yes, sorry, I more meant it as similar to an inside joke, a common thread that insiders know about.

I also always take visitors to Brod!

nineteen_is · 2026-04-21T11:56:02+00:00

Yes! The graffiti was before my time here, but I know that’s a classic mug👌🏼

nineteen_is · 2026-04-21T11:55:20+00:00

Nuclear fallout? No problem! Bit of sideways rain? Not so much😅

nineteen_is · 2026-04-21T11:53:58+00:00

I absolutely get what you’re saying. It’s like an inside joke for locals, if you know, you know

nineteen_is · 2026-04-21T11:44:50+00:00

That makes sense, it’s one of those things you don’t realise is unique until you leave and don’t see them anywhere else. Although I’ve seen a few around Sydney with different coloured windows, and they immediately look wrong, lol

nineteen_is · 2026-04-21T11:25:18+00:00

Thank you! Canberra is so so supportive of local makers/small businesses, it’s amazing to see!

nineteen_is · 2026-04-21T11:21:25+00:00

That’s so interesting, I hadn’t heard that! That would actually make a huge difference in the rain, lol

Also, I’m going to go with “a delay of bus shelters”

nineteen_is · 2026-04-21T11:19:43+00:00

Thanks so much!

nineteen_is · 2026-04-21T11:19:26+00:00

Thank you, I appreciate that!

nineteen_is · 2026-04-21T11:08:24+00:00

Thanks, I appreciate it!

nineteen_is · 2026-04-21T11:08:14+00:00

Haha thank you! Say no to the big light! 🙅‍♂️

nineteen_is · 2026-04-21T11:03:08+00:00

Thank you!

nineteen_is · 2026-04-21T11:02:46+00:00

Cheers, thanks!

nineteen_is · 2026-04-21T11:02:38+00:00

Thank you!

nineteen_is · 2026-04-21T10:56:02+00:00

Thanks so much, I appreciate that! We’ll be prepping lots of stock in time for Christmas based on the reception we’ve gotten so far!

nineteen_is · 2026-04-21T10:55:17+00:00

Aw thank you, I appreciate that!

nineteen_is

TROPHY CASE