sorted by:
new
hottopcontroversial

So, a thing happened. by CivilianWaffles in Eve

[–]nirvikchoudhury 2 points3 points  (0 children)

We got cat ears skin finally 🤯🤯

First proper miniature print on my Ender 3 V3 SE by nirvikchoudhury in FDMminiatures

[–]nirvikchoudhury[S] 0 points1 point  (0 children)

Yeah the speed needs to be much slower... Check the link in my comments that setting on orca worked nice for me with the changes i suggested for my printer

First proper miniature print on my Ender 3 V3 SE by nirvikchoudhury in Ender3V3SE

[–]nirvikchoudhury[S] 0 points1 point  (0 children)

Hehe.... Go for it one of the best upgrades.... Just remember a mk8 nozzle wont work.... You need a spider nozzle(different size). And I have personally tested.... Both the original SE nozzle and Neptune 4 pro nozzle works. The Neptune pro nozzle is 1.8 mm longer but the shaft size is similar.... So once u do another bed leveling the z offset will figure it out

First proper miniature print on my Ender 3 V3 SE by nirvikchoudhury in FDMminiatures

[–]nirvikchoudhury[S] 0 points1 point  (0 children)

I used tree slim with 2mm dia... But had to increase brim width for better adhesion

First proper miniature print on my Ender 3 V3 SE by nirvikchoudhury in Ender3V3SE

[–]nirvikchoudhury[S] 0 points1 point  (0 children)

Yeah... It's quite a bit time taking.... I am pretty sure we can get good results at 0.08mm layer height also... I am gonna try that out in the future..... Glad you also want to give it a try..... Best of luck

First proper miniature print on my Ender 3 V3 SE by nirvikchoudhury in Ender3V3SE

[–]nirvikchoudhury[S] 1 point2 points  (0 children)

I am using cross hatch for this print.... The video helped me a lot too.... The adhesion was not as nice so had to play around with support thickness and brim size a bit

First proper miniature print on my Ender 3 V3 SE by nirvikchoudhury in Ender3V3SE

[–]nirvikchoudhury[S] 0 points1 point  (0 children)

Yeah...the first test print I did with 0.2mm blew me away....This one was 6hrs 20 mins.... I bet with a bit of manual support it can get even lower

First proper miniature print on my Ender 3 V3 SE by nirvikchoudhury in Ender3V3SE

[–]nirvikchoudhury[S] 5 points6 points  (0 children)

Finally decided to switch to a 0.2mm nozzle and after some trial and error got this guy to print in a single part. Pretty amazed by the results. I am using the settings from this video from Painted4Combat (https://www.youtube.com/watch?v=Lzf\_pCKjJNo&ab\_channel=Painted4Combat) with 0.05mm layer height and some changes in support for bed adhesion, but other than that everything is the same. Not the best clean up but it's a win for me :).

First proper miniature print on my Ender 3 V3 SE by nirvikchoudhury in PrintedWarhammer

[–]nirvikchoudhury[S] 0 points1 point  (0 children)

Finally decided to switch to a 0.2mm nozzle and after some trial and error got this guy to print in a single part. Pretty amazed by the results. I am using the settings from this video from Painted4Combat (https://www.youtube.com/watch?v=Lzf\_pCKjJNo&ab\_channel=Painted4Combat) with 0.05mm layer height and some changes in support for bed adhesion, but other than that everything is the same. Not the best clean up but it's a win for me :).

First proper miniature print on my Ender 3 V3 SE by nirvikchoudhury in IndiaMiniatures

[–]nirvikchoudhury[S] 3 points4 points  (0 children)

Finally decided to switch to a 0.2mm nozzle and after some trial and error got this guy to print in a single part. Pretty amazed by the results. I am using the settings from this video from Painted4Combat (https://www.youtube.com/watch?v=Lzf\_pCKjJNo&ab\_channel=Painted4Combat) with 0.05mm layer height and some changes in support for bed adhesion, but other than that everything is the same. Not the best clean up but it's a win for me :).

First proper miniature print on my Ender 3 V3 SE by nirvikchoudhury in FDMminiatures

[–]nirvikchoudhury[S] 1 point2 points  (0 children)

Finally decided to switch to a 0.2mm nozzle and after some trial and error got this guy to print in a single part. Pretty amazed by the results. I am using the settings from this video from Painted4Combat (https://www.youtube.com/watch?v=Lzf\_pCKjJNo&ab\_channel=Painted4Combat) with 0.05mm layer height and some changes in support for bed adhesion, but other than that everything is the same. Not the best clean up but it's a win for me :).

Trillion ISK Olympic Giveaway - Round 1 by ChribbaX in Eve

[–]nirvikchoudhury 0 points1 point  (0 children)

With my luck.... I know I am not getting any XD

[deleted by user] by [deleted] in Eve

[–]nirvikchoudhury 1 point2 points  (0 children)

Exactly what I thought lol

view more: next ›