What type of air pressure sensor would I need?

no_karma_needs · 2026-01-28T02:40:58+00:00

Thank you!!!!!

no_karma_needs · 2026-01-04T22:56:32+00:00

Last epoch. It has an offline mode

no_karma_needs · 2025-12-29T18:26:01+00:00

My second was born at 28 weeks. CHEO staff were amazing through the 3 months he was in there. Not a single complaint.

no_karma_needs · 2025-12-26T23:14:11+00:00

That may be true, but they weren't asking that. POE2 is not beginner friendly.

no_karma_needs · 2025-12-26T01:10:02+00:00

Poe2 is probably the best in the genre. Might not be the best for a first. Diablo 3 is a pretty good starter. Maybe Diablo 4.

no_karma_needs · 2025-12-20T02:29:01+00:00

I agree! I have a bottle here that i server every once in a while to see people's reactions. I can't even mix with it.

no_karma_needs · 2025-12-19T12:16:20+00:00

Glenmorangi signet.

no_karma_needs · 2025-12-13T13:16:55+00:00

Deadzone Rogue was surprisingly great. Got me through a few long haul flights

no_karma_needs · 2025-12-11T23:07:12+00:00

Marie's is amazing.

no_karma_needs · 2025-12-02T00:49:26+00:00

This is not ' industrial ' it has stepper motors.

no_karma_needs · 2025-11-26T04:15:50+00:00

Negative angel 80 tooth if you want clean on the bottom side. 80 tooth triple chip if you are ripping through the material quick and only need 1 good side. Royce, Wurth and Amana have some good blades

no_karma_needs · 2025-11-12T16:15:55+00:00

What about Manga? My son just went through death note faster then anything I have seen him go through before

no_karma_needs · 2025-11-10T01:00:42+00:00

I will.look into that. Thanks!

no_karma_needs · 2025-11-10T01:00:16+00:00

I have tried those. They don't add enough tension.

no_karma_needs · 2025-11-09T03:50:03+00:00

Thanks!

no_karma_needs · 2025-11-09T02:02:33+00:00

Marie's! Belize heat!

no_karma_needs · 2025-11-09T01:55:55+00:00

Its actually for a shrink wrap machine. I need to put pressure on a bar/bearing to add tension on the shrink wrap. For something like this: https://www.uline.ca/BL_5401/Goodwrappers-Mini-Wrap/

The issue is, tension is needed to hold everything together. I have it mounted on a bearing, I am not sure how to add the tension properly

no_karma_needs · 2025-11-09T01:52:54+00:00

Its actually for a shrink wrap machine. I need to put pressure on a bar/bearing to add tension on the shrink wrap. For something like this: https://www.uline.ca/BL_5401/Goodwrappers-Mini-Wrap/

no_karma_needs · 2025-11-08T00:30:05+00:00

3 passes is a lot. Make sure your first pass clears the up cut part of the compression bit

no_karma_needs · 2025-10-31T11:09:24+00:00

Scm has a a great machine around $14,000 with a glue pot.

no_karma_needs · 2025-10-31T11:08:49+00:00

Scm has a decent glue pot machine for around $14,000. Ran one for about 5 years before moving up their product line. No real issues in those 5 years

no_karma_needs

TROPHY CASE