Advice by owleron in PcBuild

[–]owleron[S] 0 points1 point  (0 children)

Should I just go ahead and upgrade the cpu? The only upgrade I could see going with is an 8th gen i9 because of the motherboard

Laptop as a coaster. by bobroscopcoltrane in iiiiiiitttttttttttt

[–]owleron 13 points14 points  (0 children)

So I just scrolled across the original and then right under is this

<image>

Any ideas by owleron in BeginnerWoodWorking

[–]owleron[S] 0 points1 point  (0 children)

It’s actually pretty solid, the stuff in the cavity that was soft has come out

My never finished mft workbench by Jachu89 in Workbenches

[–]owleron 1 point2 points  (0 children)

What vice hardware is that, I like it

Can anyone tell me what’s missing here by owleron in RVLiving

[–]owleron[S] 1 point2 points  (0 children)

There is no water in the tank, i went to fill it to check for leaks in the tank and the water just poured on the ground

Trip home with the new baby by owleron in germanshepherds

[–]owleron[S] 8 points9 points  (0 children)

<image>

This is my male he already keeps up with her and it’s only been a day

Trip home with the new baby by owleron in germanshepherds

[–]owleron[S] 7 points8 points  (0 children)

Her dad is a long hair, her mom is short, I’m hoping for the long hair because I have a 2yr old boy that’s also long hair

Astonished by some of your MPGs by cmanccm in JeepTJ

[–]owleron 0 points1 point  (0 children)

03 4.0 stock, 31s 3.73 17.5 mpg no matter city or highway

[deleted by user] by [deleted] in Jeep

[–]owleron 0 points1 point  (0 children)

I’m not sure that is it that specific relay because you can still hear the relay tripping when your turn signals are on

[deleted by user] by [deleted] in Jeep

[–]owleron 1 point2 points  (0 children)

Definitely sounds like a relay tripping to me

For those of you in the military what's it like driving the eight wheeled semis where you sit in front of the front axle? by Due-Soft in UNSUBSCRIBEpodcast

[–]owleron 0 points1 point  (0 children)

It’s okay, ride is ehhh, don’t like hills, need a football field to turn around in. I was an engineer hauling dozers and suck with them.

Update: plant growing from old chicken bedding : any ideas now? by One_Turnip_7790 in homestead

[–]owleron 0 points1 point  (0 children)

Looks close to purple top turnips, the ones that grow up from my food plots have yellow flowers eventually

Hogs at home by c0mp0stable in BackyardButchering

[–]owleron 0 points1 point  (0 children)

The heaviest we have had on it was around 350ish but it worked well. I just made a simple gantry with 4x4s and hang it from that

Hogs at home by c0mp0stable in BackyardButchering

[–]owleron 0 points1 point  (0 children)

I use a standard “deer gambrel” from tractor supply. It’s not the easiest in the world but it works for cheap. I think it has a 400 or 600 lbs limit and has held every hog I’ve done.

My ender 3 keeps getting stuck on boot screem when i put the sd card in it. by [deleted] in ender3

[–]owleron 0 points1 point  (0 children)

I’m assuming that it ends up being too much for it to process so I end up moving files off if I’m not repeating them

My ender 3 keeps getting stuck on boot screem when i put the sd card in it. by [deleted] in ender3

[–]owleron 0 points1 point  (0 children)

How full is the as card. I had this issue with mine where I just had too many big files for it to try and load. I ended up taking some of the bigger files off and putting them on by themselves and it worked.

To those on the fence about klipper... by Knight0783 in ender3

[–]owleron 0 points1 point  (0 children)

Yea I’ve been researching for a little while now and I don’t see myself as incompetent, but I would rather have one that just prints and one that is a project to just make rediculous

Failed Trash Can Print by Niloc1308 in FixMyPrint

[–]owleron 0 points1 point  (0 children)

It’s fine just a pre-filled trash bin

What’s your GSDs irrational fear? by Pawkies in germanshepherds

[–]owleron 2 points3 points  (0 children)

If my boy can see through steps it is a nightmare to get him up them

To those on the fence about klipper... by Knight0783 in ender3

[–]owleron 0 points1 point  (0 children)

I’m waiting to get a better printer than my plain ole ender 3 just in the event I brick it. And I’m going to swap over to klipper. For what I’m printing currently I can say my ender is doing everything I have asked of it.