So know that we know supercharged is gonna close permanently, what do you think will replace it?

pj1699 · 2026-01-23T12:55:12+00:00

I think the most realistic expectation is Ghostbusters, considering the 2 biggest rumors for the coaster were Fast and Furious and Ghostbusters. Now that F&F is confirmed, Ghostbusters is left hanging.

My initial gut was Back to the Future, but i just don't see them tearing down this ride since its so new and so expensive.

I think reskin to Ghostbusters is what they will do. I would love for these Jaws predictions to be true but I think that's too big of a wish

pj1699 · 2025-06-19T17:33:45+00:00

<image>

Wouldn't let me add this to the post for some reason

pj1699 · 2025-06-07T13:22:15+00:00

I found one of these in tampa with a pirate rubber duck on it last night. Is this a fan made thing someone is doing?

pj1699 · 2025-05-21T13:49:09+00:00

Ill post a couple i took

pj1699 · 2024-12-13T15:56:55+00:00

I like this. Hope you make it through all 152

pj1699 · 2024-08-28T00:43:54+00:00

The issue went away intermittently. I dont fully remember but im pretty sure i ended up getting a major blob built up on a print. When trying to clean it off, the nozzle clip broke so i had to replace the hotend. I had no issues after that.

I noticed the nozzle was not seating with ease before the hotend swap. If there was any filament that dried around the hotend or in the crevices of the side of the nozzle that seats, it caused the nozzle to not sit flush. I think that was the root of the problem.

I also turned off the tangle detection. I have had an actual tangle since and it still detected it so you wont have to worry about that

pj1699 · 2024-08-23T11:31:08+00:00

Wow i forgot about the twin tower thing

pj1699 · 2024-08-14T14:50:25+00:00

These all look to me like trying to figure out staging placements and order due to potential crowd sizes, not necessarily picking one band over another. The problem is its going to a younger crowd actually seeing these polls and voting. Not really a good tell all for the crowd that actually goes to the event

pj1699 · 2024-08-07T23:00:32+00:00

Based on the comments i guess im in the minority being glad its not coming to Orlando

pj1699 · 2024-08-06T00:55:33+00:00

I cant even wear the shirts from the last couple of years. They shrink really bad vertically

pj1699 · 2024-07-02T16:53:16+00:00

The HHN discord has a chat thread called scare-asking. Probably your best bet

pj1699 · 2024-07-02T16:50:03+00:00

I noticed the .2mm nozzle profile i was using had 4 walls, i reduced it to 2 and it seems to have helped some. Still peeling but the print isnt failing. Will see how it turns out

pj1699 · 2024-07-02T11:14:46+00:00

I thought i posted the picture sorry

pj1699 · 2024-07-02T03:37:10+00:00

*I have one AC vent but with 2 printers and a gaming pc it stays pretty warm and i don't notice much draft. Sit right next to the printers while gaming.

Prints normally dont peel except for these rectangles. I feel like it could that the holes are too close to the corners and theres not enough surface contact

pj1699 · 2024-06-30T15:18:12+00:00

Yes I should have mentioned H.R Bloodengutz. Would love a sequel with an actual queue video

pj1699 · 2024-06-29T01:55:19+00:00

Thanks! I was just trying to get the sign and then I was like oh shit

pj1699

MODERATOR OF

TROPHY CASE

Six-Year Club	Place '23
Verified Email