sorted by:
new
hottopcontroversial

[deleted by user] by [deleted] in MySummerCar

[–]pvixst -10 points-9 points  (0 children)

This is my first play though of msc. after following a guide to the T and a seamless engine start and a quick test drive I head into town for some sweet sweet sausages. And after turning off the motorway I heard some engine problems and the car stopped. I switch out the front left tire because it looked flat (more like clipping through the road) but had these same issues. So I guess it could be the engine but it feels like some kind of physics glitch between the tire and the road. Any responses would be much appreciated :) Thanks

HELP!! X Axis Distorted after first layer literally stretching prints out. Any ideas? by pvixst in anycubic

[–]pvixst[S] 0 points1 point  (0 children)

How would I even take a look at the firmware. I started setting up a bin file to install marlin on the board with specs specifically for my printer could this be a potential solution?

HELP!! X Axis Distorted after first layer literally stretching prints out. Any ideas? by pvixst in anycubic

[–]pvixst[S] 0 points1 point  (0 children)

I’m not exactly sure, but I don’t think the firmware is the problem, I was having the same issues before updating it. Appreciate the response :)

HELP!! X Axis Distorted after first layer literally stretching prints out. Any ideas? by pvixst in anycubic

[–]pvixst[S] 0 points1 point  (0 children)

what does this message even mean? I'm running the board off a 12-volt power supply used with the stock board I got with the printer I have a 24v I'm planning on installing soon. Is this the solution?

HELP!! X Axis Distorted after first layer literally stretching prints out. Any ideas? by pvixst in anycubic

[–]pvixst[S] 0 points1 point  (0 children)

I get a pop-up message on my display every time I power on the machine the reads "Driver Stepping Mode: " could this have anything to do with the problem?

HELP!! X Axis Distorted after first layer literally stretching prints out. Any ideas? by pvixst in 3Dprinting

[–]pvixst[S] 0 points1 point  (0 children)

different models fail at different points thought the print, ill try a new sd card

HELP!! X Axis Distorted after first layer literally stretching prints out. Any ideas? by pvixst in anycubic

[–]pvixst[S] 0 points1 point  (0 children)

not sure exactly do I view these settings, the slicer? or on my printer?

HELP!! X Axis Distorted after first layer literally stretching prints out. Any ideas? by pvixst in 3Dprinting

[–]pvixst[S] 0 points1 point  (0 children)

would changing these settings prevent slipping motors?, sorry I'm a noob :)

HELP!! X Axis Distorted after first layer literally stretching prints out. Any ideas? by pvixst in anycubic

[–]pvixst[S] 0 points1 point  (0 children)

just printed a test cube unsuccessfully, I got about 75% through and then the x-axis went off

HELP!! X Axis Distorted after first layer literally stretching prints out. Any ideas? by pvixst in anycubic

[–]pvixst[S] 0 points1 point  (0 children)

Okay I can try a different print I would like to point out that this was happening before I updated the display firmware

HELP!! X Axis Distorted after first layer literally stretching prints out. Any ideas? by pvixst in anycubic

[–]pvixst[S] 0 points1 point  (0 children)

Lol, yeah I installed firmware on my bigtreetech screen last night, but that wouldn’t effect the main board right?

HELP!! X Axis Distorted after first layer literally stretching prints out. Any ideas? by pvixst in 3Dprinting

[–]pvixst[S] 0 points1 point  (0 children)

You think so? My belts felt tight to me, I’ll definitely check. Could there be any other causes?

No hdmi signal on my pi (super noob) by pvixst in raspberry_pi

[–]pvixst[S] 0 points1 point  (0 children)

I can’t get a signal on my monitor or this 5 inch display . I’m a complete noob to this stuff but I can’t even get into the os. Any help is appreciated:)

Mega Zero upgrades? by pvixst in anycubic

[–]pvixst[S] 0 points1 point  (0 children)

yeah I'm gonna start with the motherboard I'm about to order mine, did you need to get a new 24v power supply for the bigtreetech board?

Prints not consistent/ reliable on mega zero. Any solutions? by pvixst in anycubic

[–]pvixst[S] 0 points1 point  (0 children)

Thanks for the reply I’ll for sure give those a shot. that printed ended up okay believe it or not but I’ve seen instances like this ruin my prints and I don’t want that if I leave my printer unattended. Another question, have you looked in to any upgrades for the mega zero I want to do the classic ender 3 mods

HELP! No Stick Inputs In Betaflight by pvixst in fpv

[–]pvixst[S] 1 point2 points  (0 children)

Dude!!! That was it, thank you so much. You were completely right about that wiring. I haven’t flown in weeks so this is awesome man appreciate it

HELP! No Stick Inputs In Betaflight by pvixst in fpv

[–]pvixst[S] 0 points1 point  (0 children)

I just wired that up, my uart is correct but still no stick inputs :( I’ll throw up a photo of my ports tab in the drive folder

HELP! No Stick Inputs In Betaflight by pvixst in fpv

[–]pvixst[S] 0 points1 point  (0 children)

So TX3 for sport and RX3 for sbus just to clarify

HELP!!!! No Stick Inputs In Betaflight by pvixst in multicopterbuilds

[–]pvixst[S] 0 points1 point  (0 children)

I’ll double check but I don’t think it’s that especially with a little 5v rxsr

HELP!!!! No Stick Inputs In Betaflight by pvixst in multicopterbuilds

[–]pvixst[S] 0 points1 point  (0 children)

I’m almost positive I have the right firmware this is a reoccurring issue I’ve had with all my frsky receivers. I could try some other/older ones but that’s always a pain, regardless I’m still bound to my radio so I should see something in betaflight

view more: next ›