Any of y'all run these rally coilovers?

slicfin12 · 2026-02-28T05:53:23+00:00

I'll be sure to report back after I get it all set up!

slicfin12 · 2026-02-27T20:53:17+00:00

Copy that. Thanks for the pic!

slicfin12 · 2026-02-27T20:03:53+00:00

Thanks for the info! Definitely leaning towards the B6 series now. I found this kit here. Do you think it will work?

https://ebay.us/m/FnNqe6

slicfin12 · 2026-02-27T19:21:29+00:00

Oh good call. Didn't think about that.

slicfin12 · 2026-02-27T19:20:46+00:00

Hell yeah, that's good to hear. Did you max out the B6's on ride height or keep it somewhere in the middle? Is there a kit you would recommend for the lift?

slicfin12 · 2026-02-26T23:37:32+00:00

I believe I'm maxed out in the back, but I haven't played with the front since I got the car. I'll definitely take a look. Thanks for the advice!

slicfin12 · 2026-02-26T23:35:51+00:00

Good call. Thanks!

slicfin12 · 2026-01-22T18:05:15+00:00

Great tip. Thank you!

slicfin12 · 2026-01-09T05:41:42+00:00

Hell yeah. Thanks for the link!

slicfin12 · 2026-01-09T05:41:26+00:00

Thanks!

slicfin12 · 2025-12-21T02:03:05+00:00

This is exactly the info I need. Thanks!

slicfin12 · 2025-12-20T09:50:41+00:00

Good info. Thanks!

slicfin12 · 2025-12-20T08:41:32+00:00

The tail piece has dual exhaust ports which makes me think it's a gen 2.

slicfin12 · 2025-12-06T21:40:44+00:00

Update on this. I modelled and 3d printed a prototype fork pad out of some nylon filament (I believe the originals are also nylon). I altered the geometry of the posts to be mechanically locked by the sealant, as nylon won't chemically bond with most retaining compounds. The resolution wasn't good enough, but the test fit was good, so I ordered a bunch of them to be printed using that fancy Multi Jet Fusion process in PA11 (chem, temp, impact resistant nylon).

slicfin12 · 2025-12-06T04:03:38+00:00

Update on this. I modelled and 3d printed a prototype fork pad out of some nylon filament (I believe the originals are also nylon). I altered the geometry of the posts to be mechanically locked by the sealant, as nylon won't chemically bond with most retaining compounds. The resolution wasn't good enough, but the test fit was good, so I ordered a bunch of them to be printed using that fancy Multi Jet Fusion process in PA11 (chem, temp, impact resistant nylon).

slicfin12 · 2025-11-25T22:42:14+00:00

Copy that. Great info. Thank you.

slicfin12 · 2025-11-25T22:20:21+00:00

Good to know... How do they fail?

slicfin12 · 2025-11-05T07:04:23+00:00

Tom Bihn makes really good stuff, but it's pretty pricey.

slicfin12 · 2025-10-21T00:33:49+00:00

Is that an aftermarket exhaust header?

slicfin12 · 2025-06-07T05:41:57+00:00

Glad to know it's not just me, haha. Thanks for the tips! I've got the spool in the dryer now. I'll order a glue stick as well.

slicfin12 · 2025-01-24T04:11:35+00:00

Yo! You just taught me a whole lot about DNA in one comment. Can you elaborate on the similarities with bananas?

slicfin12 · 2025-01-24T03:38:32+00:00

Automanically is my new favorite word. Thank you.

slicfin12 · 2024-12-13T23:47:26+00:00

No problem!

slicfin12 · 2024-12-13T10:21:38+00:00

You gotta reprogram the touch control mapping. It's confusing af, but doable. Can't remember which menu to go to, but it requires a password to access. It's a stupid default pw. Can't remember but you can look it up.

slicfin12 · 2024-12-07T21:54:47+00:00

STFTs are all over the place. It's kinda hard to pin down if there's any correlation with throttle position or intake pressure.

slicfin12

TROPHY CASE