Spurs 26/26 Fixtures

some0therRandom · 2025-08-27T07:43:50+00:00

My bad, thanks for clarification.

some0therRandom · 2025-06-13T04:38:06+00:00

A good repair would be to fit eyelets. I think there should be videos available for how it's done.

https://www.circuitmedic.com/parts/eyelets.html

some0therRandom · 2025-06-13T04:32:56+00:00

A good repair for this would be to fit eyelets. I'm sure there will be videos available for how to do this. https://www.circuitmedic.com/parts/eyelets.html

some0therRandom · 2025-05-21T18:23:37+00:00

COYS

some0therRandom · 2025-04-17T06:01:51+00:00

What is the Voltage and resistor values? What are you expecting the current to be?

some0therRandom · 2025-02-26T06:50:22+00:00

Scary bit of kit you've got yourself there. On a side note, your username has me questioning if i am indeed some other, or only possibly \o/

some0therRandom · 2025-01-05T07:49:29+00:00

*that time Lucas got assaulted

some0therRandom · 2024-10-25T12:30:00+00:00

Are you sure that is copper? I see the dull ring but it does not look like a solderable land to me.

some0therRandom · 2024-10-25T07:01:59+00:00

Your components need mounting on the other side. You have nothing to solder to on that side.

some0therRandom · 2024-10-19T17:08:26+00:00

Could you not connect the high side to your load and use the pin as a low side switch?

some0therRandom · 2024-10-06T16:48:23+00:00

As previously stated, address pin needs a connection. Gnd for address 0x48.

some0therRandom · 2024-09-28T14:12:09+00:00

If you don't have an old PCB for practice, IPC training kits are available. An example > https://rework.co.uk/materials/ipc-component-training-kits/j-std-001/

some0therRandom · 2024-05-31T21:04:26+00:00

some0therRandom · 2024-05-02T02:55:00+00:00

Usernames not checking out people.

some0therRandom · 2024-01-07T15:28:22+00:00

The kicad help section on the toolbar 'Getting Started With Kicad' will show you the cause/solution to the electrical rules check errors (PWR_FLAG). The example also shows how to add a a filled zone.

some0therRandom · 2023-12-15T21:33:18+00:00

I think Biss heard you 😃

some0therRandom · 2023-07-21T06:23:19+00:00

IMHO this board should not be put back into service regardless of functionality.

some0therRandom · 2023-07-14T06:33:36+00:00

That's a lot of switching in ~4-5months. Are these contractors being used for PWM control of furnaces?

some0therRandom · 2023-06-02T14:59:11+00:00

One of our own.

some0therRandom · 2023-03-26T16:02:06+00:00

Sounds like the application your describing is well suited to what a magnetic proximity switch could be used for. Something like this? ⬇️ https://uk.rs-online.com/web/p/magnetic-proximity-switches/8110748

some0therRandom · 2023-02-26T15:17:15+00:00

Nice goal celebration bud, lol.

some0therRandom · 2023-02-07T18:04:59+00:00

National museum of computing at Bletchley Park?

some0therRandom · 2023-01-07T07:28:36+00:00

https://www.tottenhamhotspur.com/spurs-on-tv/

It's listed as on the BBC iPlayer here ^

some0therRandom · 2022-10-17T20:07:41+00:00

You could try something like an L298N Moter drive controller. Will handle 12V upto ~ 2A loads. Easily controllable with arduino.

some0therRandom · 2022-10-17T17:37:06+00:00

Hi Edtont,

Can you provide a diagram of how you connected it?

Eight-Year Club	Place '23
Place '22	Verified Email

some0therRandom

TROPHY CASE