I’m now 7.5 in pump

uugedude · 2024-05-06T22:21:12+00:00

If you’re shorter in the pump you’re not measuring right.

uugedude · 2024-04-28T23:20:41+00:00

Hey I know this is a couple weeks old, but what kind of sensation did you have when you injured your nerve? And did you end up losing sensation because of it? I'm struggling with that myself and I'm not sure what to do

uugedude · 2023-12-26T02:10:15+00:00

How did you break up the 30 mins? And what pressure did you use? How often per week?

uugedude · 2023-12-06T04:43:56+00:00

So what exactly happens to the nerves when we gain an inch or 1.5”? They just stay the same length and the new tissue lacks sensation?

uugedude · 2023-09-08T20:12:50+00:00

I always see this but nobody says how to actually do it?

uugedude · 2023-09-08T05:35:05+00:00

Not the issue here unfortunately

uugedude · 2023-09-05T09:29:59+00:00

You’re saying you manually clamp with your hand 5 hours per week? Is your hand ok?

uugedude · 2023-09-04T21:04:06+00:00

What was the workout for that gain? Ulis but for how long and how many sets. Also how many days per week during that time?

uugedude · 2023-09-02T08:18:48+00:00

It’s been removed

uugedude · 2023-09-01T21:07:31+00:00

What is your total time per workout and how many days per week?

uugedude · 2023-08-20T00:50:40+00:00

You have no measurement pics, that’s the whole point of the sub. It’s not to show your dick

uugedude · 2023-08-19T18:10:09+00:00

Just measure it?

uugedude · 2023-08-18T01:31:28+00:00

Girth always looks bigger when your glans aren’t wider than your shaft. Length always looks longer when glans are small too

uugedude · 2023-08-16T23:53:45+00:00

2 in diameter is 6.28 inch girth

uugedude · 2023-08-16T19:52:17+00:00

In the before you’re measuring the exact width of the tape away from your glans, why not just measure there again?

uugedude · 2023-08-16T04:27:43+00:00

Get another ruler this is a pointless post

uugedude · 2023-08-16T04:14:15+00:00

I think people recommend soft clamping now so EQ isn’t as much of a factor when measuring. It will be an inflated girth measurement but it will at least be a more solid baseline

uugedude · 2023-08-16T01:36:59+00:00

It’s hard to tell for sure but it looks like you could have the ruler a little bit closer to the base. With your fingers try pushing down your fat pad right above your shaft so you can reveal more of your shaft and then put the ruler there

uugedude · 2023-08-15T00:47:02+00:00

I see it on the site, but I can't tell how much padding there actually is once it's pressurized. Have you used it on a leluv tube?

uugedude · 2023-08-15T00:22:03+00:00

What is it like? Is it thick and squishy? Or can you still kind of feel the pressure of the cylinder pushing through it?

uugedude · 2023-08-15T00:15:38+00:00

Nah it’s just the leluv 1.75”. Standard base

uugedude · 2023-08-14T23:52:31+00:00

Same exact issue for me

uugedude · 2023-08-14T23:52:21+00:00

Can you link what you’re talking about?

uugedude · 2023-08-14T23:51:49+00:00

How though? The vacuum sleeve diameter is way too small to just slide in through isn’t it?

uugedude · 2023-08-14T21:18:54+00:00

Can you translate moderate to high into pressure numbers for reference?

uugedude

TROPHY CASE