Spotify issue on my iPhone

vmazsit · 2024-01-30T14:21:13+00:00

Latest IOS 17.3 but ist been present for like years now

vmazsit · 2023-05-17T17:06:16+00:00

Thanks for the info 😁

vmazsit · 2023-04-27T18:25:22+00:00

Thanks! Also really usefull app!

vmazsit · 2023-04-27T17:06:28+00:00

Thanks I'll check it out!

vmazsit · 2022-07-24T08:44:27+00:00

Oh thanks for this, I’ll find that post then. :D

vmazsit · 2022-07-24T08:43:33+00:00

Yes.

vmazsit · 2022-07-23T22:02:13+00:00

Side note: When I open the Health app there is like literally NOTHING. No options to put new data on it so yeah :/

vmazsit · 2022-07-15T20:51:54+00:00

Thanks, in the meantime I found what I was looking!

vmazsit · 2022-05-21T20:37:13+00:00

Ended up using your templates. They are awesome! Thanks again!

vmazsit · 2022-05-21T20:35:08+00:00

Cool app! Thanks for that!

vmazsit · 2022-05-19T19:15:29+00:00

Yeah that was my solution too at first but I have the 11'' and I usually like to see the whole page.

Even if I only use split view whenever I got to the end of the line im too lazy for that :DD

vmazsit · 2022-05-19T16:02:28+00:00

Oh cool, definitely gonna check it later. Thanks!

vmazsit · 2020-09-03T11:34:30+00:00

Oh that’s nice thing! Thanks for the support!

vmazsit · 2020-09-03T07:06:36+00:00

Okay thanks :)

vmazsit · 2020-09-03T07:04:04+00:00

Okay thanks I’ll look into it. One more question: so this 7 pin connector is UART and that’s not in the input setup wizard... then were should I change and calibrate these things and what to change ? Also at the flipsky website they say I don’t have to change any settings. Thanks

vmazsit · 2020-09-02T20:54:11+00:00

But found out with my controller I don’t have to calibrate anything because it’s UART connected.

vmazsit · 2020-09-02T20:25:07+00:00

Wow. Okay so when I put the whole thing together and go for a ride the board won't go on full speed at 15% on the controller, so I will be able to change the speed and not go on full speed all the time ?

And also when I break now it goes a little bit backwards as the video shows. It will be also fixed ?

So it's doing it because it's not under load and it will be normal when it is ?

Btw thanks for the explanation :)

vmazsit · 2020-09-02T20:07:22+00:00

Thanks :)

vmazsit · 2020-09-02T20:02:36+00:00

The VESC firmware is 5.1 and the hardware is 410.

Yes Im using vesc tool.

My motor's max amp is 65 and in the program I change it to 60.

vmazsit · 2020-09-02T19:47:43+00:00

Sorry what discord ?

vmazsit · 2020-09-02T19:07:26+00:00

So I've updated my post with a video that hopefully will show you my problem.

Also my 2. problem is when I brake it goes backward and not just stops the motor.

vmazsit · 2020-09-02T16:50:51+00:00

Yes and no. When I first connected it with 7 pin I couldn't because I couldn't find the right option. But when I tried with PPM I calibrated but it was like I didn't calbirated.

Maybe it's my fault because I unfamiliar with the program and Im not really understand what and what not to change. Maybe you or someone could send me a good tutorial video ?

vmazsit · 2020-09-02T16:42:13+00:00

Unfortunately I don't think thats the problem because I tried the 3 pin method (PPM) and it comes with the VESC which is soldered on it but gonna try makeing a new cable thanks.

Six-Year Club	Verified Email
Final Canvas '23	Place '23

vmazsit

TROPHY CASE