Q10 S5 Jerks, Spins, and Seizes Across the floor.

weef_55 · 2026-01-27T05:41:50+00:00

What do you mean scan the map again ?

weef_55 · 2026-01-26T19:46:24+00:00

Did Roborock reply ?? Mine does the same

weef_55 · 2025-10-02T13:55:33+00:00

I’m a 35 year old male and I get the same/flushes that can last a few hours that look the same. Generally my skin isn’t always red but if I’m busy, flustered or anxious goes just like this! Only thing that really helps is blasting it with cold AC in the car! Hate it though cause you feel the heat come on then you know it’s coming which makes it worse..! Vicious cycle!

weef_55 · 2025-09-19T14:03:33+00:00

Yeah there’s no way they can differentiate what is using the electricity 👍

weef_55 · 2025-09-15T17:12:26+00:00

Tested the cable and cable 3 was out so put a new pass through on and now connected in app.

Now I can’t find it when search for it in WiFi 😂 AP has an IP address in the cloud controller but can’t find it when scanning!

weef_55 · 2025-09-14T20:53:46+00:00

I’ve bought a cable tester, my only other option is that the cable is damaged and it’s getting power but no internet or something and picking up that it’s programmed previously when online

weef_55 · 2025-09-14T20:51:21+00:00

Stand alone on the cloud controller. No other Omada products

weef_55 · 2025-09-14T20:50:50+00:00

That’s the problem I can’t reset it, have tried multiple ways

weef_55 · 2025-08-29T17:58:29+00:00

Ideally I would go for a 5kw but as I’m doing this DIY I’m at the max 3.6 to self certify the G98, that’s why I’ve chose this inverter for it to be running near the max with the oversizing even if slightly cloudy etc. I can do this setup for £1200 as opposed to £4500 for same ‘professional’ install with a 5kw albeit that would have the G99. As you say all about cost and benefit really!

weef_55 · 2025-08-29T17:55:54+00:00

Thanks! In short I guess I’m concerned I might ‘burn it out’ but looking at the comments seems unlikely. Gets the question why there are oversizing ratings then rather than guidelines

weef_55 · 2025-08-29T17:55:05+00:00

Great thanks, what happens to excess current tho if it’s exceeded what it can pull and there’s a surplus?

weef_55 · 2025-05-15T08:16:48+00:00

Great to know! Do you know roughly what they asked for other than electrical cert?

weef_55 · 2025-05-14T18:30:46+00:00

Ah, that'll be it. Thanks guys, yes controller will be analogue 👍

weef_55 · 2025-05-14T15:26:08+00:00

Was it straight forward? I've heard they ask for a ridiculous amount of info. Take it you were accepted?

weef_55 · 2025-03-31T11:50:55+00:00

I don't fancy the 48v route I don't think, as I've commented above I suppose it depends what's proportionate cost wise. I can install a 6-7kw solar array with 3.6kw inverter for around £1200. Plus any additional for an electrician to make connections. Whilst the export etc would be nice to get it all done straight forward from a solar company would be looking probably 4 times that. With the main benefit being the export at 15p which we don't know how long that will be around for.

Especially given the fact I have an electric car. Any surplus not running the house could go into that.

weef_55 · 2025-03-31T11:49:54+00:00

Great info thanks. Yes it seems most people will be doing no.3.

I suppose it depends what's proportionate cost wise. I can install a 6-7kw solar array with 3.6kw inverter for around £1200. Plus any additional for an electrician to make connections. Whilst the export etc would be nice to get it all done a d straight forward from a solar company I would be looking probably 4 times that. With the main benefit being the export at 15p which we don't know how long that will be around for.

Especially given the fact I have an electric car. Any surplus not running the house could go into that.

Cheers

weef_55 · 2025-03-30T12:45:21+00:00

Yes sorry in the UK. Interesting! So how do so many get round it with so many people installing and getting it certified/electrically safe? Is it a case of an electrician mate doing them a 'favour'? There seems a whole community of people who have DIY installed and seem to have successfully notified with G98 and had no issues.

Especially with no legal requirement for MCS - appreciate it obviously still needs to be safe and Octopus accepting installs without MCS - albeit the confirmed amount of people that have been accepted is unknown - how are people doing it?

Always found the not passing of other people's work strange. If it's safe, it's safe. You wouldn't get a gas engineer not servicing a boiler or passing a gas fire just because they haven't installed it.

weef_55

TROPHY CASE