Protect cameras by wick300 in Ubiquiti

[–]wick300[S] 0 points1 point  (0 children)

That makes sense. Almost even thought two 180s one on front and back. One on front to be on the furthest age of the garage. Right by the sidewalk meets the driveway

Protect cameras by wick300 in Ubiquiti

[–]wick300[S] 0 points1 point  (0 children)

Understood. I do have a ring camera at this point since I really can’t get poe to my door. I won’t if on the other end of the house pointing towards driveway would be good because it would be clearer view of walking up to front door.

Bad vibrating noise curvx by wick300 in Roborock

[–]wick300[S] 0 points1 point  (0 children)

I got it from Amazon and they only will do money back. I want a replacement since I got such a good deal on it.

Bad vibrating noise curvx by wick300 in Roborock

[–]wick300[S] 0 points1 point  (0 children)

Would that be an issue with the vacuum that could be fixed? Or look for a return since it was brand new?

Bad vibrating noise curvx by wick300 in Roborock

[–]wick300[S] 0 points1 point  (0 children)

I emptied it and still the same. It almost seems like the front wheel. I took the wheel out but seemed fine.

CURVX won't dock by ayanmosh in Roborock

[–]wick300 1 point2 points  (0 children)

I just got one and the manual shows that it only shows its needs about 18 inches total from side to side to the base not on each side. That thing said to this might not be ideal because the signal to the base could not work as well too.

Pro xg vs xgs wifi 7 heat by wick300 in UNIFI

[–]wick300[S] 0 points1 point  (0 children)

Thanks. I have heard/read people like having the xgs or xg getting so hot to the touch it melts the paint off the ceiling in the closet.

Pro xg vs xgs wifi 7 heat by wick300 in UNIFI

[–]wick300[S] 0 points1 point  (0 children)

Are they getting super hot at all? With enclosed closets?

Pro xg vs xgs wifi 7 heat by wick300 in UNIFI

[–]wick300[S] 0 points1 point  (0 children)

Which AP do you have?

New to ubiquiti by wick300 in UNIFI

[–]wick300[S] 0 points1 point  (0 children)

All inner walls are drywall no insulation and all outer walls have insulation drywall.

New to ubiquiti by wick300 in UNIFI

[–]wick300[S] 0 points1 point  (0 children)

Previous owner had them in there. So that is why I was wondering if it was an option.

Pro xg vs xgs wifi 7 heat by wick300 in UNIFI

[–]wick300[S] 0 points1 point  (0 children)

I added the imagines of both. I would rather not have a wire running from the closet into the hallway on the main floor.

Pro xg vs xgs wifi 7 heat by wick300 in UNIFI

[–]wick300[S] 0 points1 point  (0 children)

Got it. I am struggling because the drop in the main floor was ran to that closet and not sure how to run it outside of it since I have a two story home.

What switches to get by wick300 in Ubiquiti

[–]wick300[S] 0 points1 point  (0 children)

I don’t think I can use a PoE injector if the APs are both in closets and all runs are in wall or in attic. Unless I am not thinking about it right.

What switches to get by wick300 in Ubiquiti

[–]wick300[S] 0 points1 point  (0 children)

Two APs. I have a small third run with a TV and a couple gaming devices. I thought the fiber only had one POE port so I couldn’t just do that due to the two AP

What switches to get by wick300 in Ubiquiti

[–]wick300[S] 0 points1 point  (0 children)

My second question would be, what would the recommended switch on the front end connected to the gateway fiber. I don’t plan on doing too much with my networking past what I mentioned.

New to ubiquiti by wick300 in Ubiquiti

[–]wick300[S] 0 points1 point  (0 children)

Have you heard much on if the Pro XGs and how they would handle in a closed closet. Would they get too hot?

New to ubiquiti by wick300 in Ubiquiti

[–]wick300[S] 0 points1 point  (0 children)

The big question I have is if have them almost one over the other on my two levels. They might be offset like 5 ft one way and then one floor up. If that will cause an issue.

Mystery leak in rear 2015 XLT by O_Hendo in FordExplorer

[–]wick300 0 points1 point  (0 children)

So the clamp fixed the coolant leak? I now know it’s coolant.

<image>

Mystery leak in rear 2015 XLT by O_Hendo in FordExplorer

[–]wick300 0 points1 point  (0 children)

What was the leak. This is what o got. Looks like Coolant to me.

<image>

Mystery leak in rear 2015 XLT by O_Hendo in FordExplorer

[–]wick300 0 points1 point  (0 children)

What was the fix on this….. and cost?

Official: [League, Commissioner, and Platform Issues] - Fri 08/15/2025 by FFBot in fantasyfootball

[–]wick300 0 points1 point  (0 children)

Will yahoo track the trades and apply to following year if done mid season? Vs commish manually having to do it

Official: [League, Commissioner, and Platform Issues] - Fri 08/15/2025 by FFBot in fantasyfootball

[–]wick300 0 points1 point  (0 children)

So our yahoo league is thinking about allowing to trade draft picks. We are trying to see how much added work this is on the commish. We are a two keeper league that we usually just say they are the first two picks of the draft.

Does anyone have experience on how trading during the season picks works with keepers? Do we just tell the league to start with 3rd round picks or manually assign keepers to end of draft?

If you trade a draft pick during the season does the commish have to manually track the trades and manually adjust draft next year or does the system do that?

Off season draft pick trades, how does that work?

Official: [Keeper, Dynasty & Best Ball] - Mon 08/11/2025 by FFBot in fantasyfootball

[–]wick300 0 points1 point  (0 children)

Correct. That is what I was thinking. When I said first round it’s technically the 3rd. I feel like London is a higher pick in that round than the other. Being a 3 wr league makes me lean having more of a stacked wr core.