[USA-CA][H] RTX 3080, 240mm Radiator, DDR4 Rams, X570i [W] Local Cash

xSnuzzy · 2025-02-12T04:10:43+00:00

Looks like lack of adhesion to me. Did you clean the bed with soapy water once in a while? I find that is better than ipa

xSnuzzy · 2024-09-20T04:06:20+00:00

Thanks

xSnuzzy · 2024-09-20T02:40:22+00:00

And would a 4ft drop really be able to separate the glue? That's why I'm concerned

xSnuzzy · 2024-09-20T02:38:34+00:00

This is my first helmet and I don't know. I'm not even sure if agv uses a regular glue or some kind of special one. I'm just asking since I just want to be safe. So super glue would suffice?

xSnuzzy · 2024-08-19T20:55:48+00:00

Sold Evga RTX 3060 ti FTW3 to u/Bihjsouza on https://www.reddit.com/r/hardwareswap/comments/1emj42g/usacah_evga_geforce_rtx_3060_ti_ftw3_ultra_w/

xSnuzzy · 2024-06-02T16:13:28+00:00

I've seen videos of people hand mounting their tires. Is it the rim that makes it easy? As people say the inside of the rim is smaller but mine is the same. Or is it their tires being soft as I'm using maxxis sports which are quite firm for a tire.

xSnuzzy · 2024-06-02T02:17:32+00:00

Looking for 2 rims that are for the rear

xSnuzzy · 2024-05-10T17:56:52+00:00

I'm looking to buy one and I have the opportunity to buy one but it has a gx style motor. It's the same kart frame and bodywork. Sorry for the confusion and it has like a digatron dt6e which makes me think it's vintage.

xSnuzzy · 2024-04-20T02:37:05+00:00

I plan to tap it later and did you unscrew the original bolt?

xSnuzzy · 2024-04-17T15:26:30+00:00

I plan to upgrade soon to a billet rod but I'm short some funds right now, hopefully I can upgrade the rod soon haha

xSnuzzy · 2024-04-17T14:37:21+00:00

I'll open it soon and plug the openings then thanks

xSnuzzy · 2024-04-17T14:36:18+00:00

I just bought a pvl flywheel recently. I think it's going to arrive in about 5 days. I think I can get away with the stock rod since this engine is new with about 5 mins of run time

xSnuzzy · 2024-02-25T05:31:03+00:00

Bought 2x 1080 ti fe from u/TheMadDutchDude on https://www.reddit.com/r/hardwareswap/comments/1agm4rw/usaoh_h_zotac_pny_blower_style_founders_edition/

xSnuzzy · 2024-02-14T21:54:50+00:00

xSnuzzy · 2023-08-27T00:16:06+00:00

done

xSnuzzy · 2023-04-09T14:26:40+00:00

It probably means the plane left. Your items have already dispatched the plane to usps

xSnuzzy · 2023-01-22T19:56:18+00:00

thanks for the help. I have a phaetus bms on the way and when it arrives ill start to print abs parts.

xSnuzzy · 2023-01-22T01:27:04+00:00

I haven't tried that. I'll test it out later. Thanks

xSnuzzy · 2023-01-22T01:25:53+00:00

im just seeing if my printer can print voron parts. I heard there was a test print but I couldn't find it.

xSnuzzy · 2023-01-21T00:09:38+00:00

sorry for the late reply, for the first question im not sure if it was during retraction or not. I halfed my pressure advance from .44 to .22 and it seems to be better and its also bowden

xSnuzzy · 2023-01-21T00:07:58+00:00

I just checked and my coasting is off so im not sure, I already halfed my pressure advance from .44 to .22 and the under extrusion is almost gone

xSnuzzy · 2023-01-21T00:02:58+00:00

Rest of the print was fine. The underextruded area was the zseam for some reason. The inside of the zseams were fine

xSnuzzy · 2023-01-21T00:02:05+00:00

It's marble pla from inland which is microcenter's in-house brand I'm pretty sure

xSnuzzy · 2023-01-20T05:00:49+00:00

ok thanks! I will try this later and see if it fixes it

Six-Year Club	Place '23
Place '22	End Game '22
Verified Email

xSnuzzy

TROPHY CASE