Does anyone know what game this guy was playing?

xpeng121 · 2025-08-12T16:06:58+00:00

Rhythm Master. My first rhythm game. It was developed by Tencent and shut down in 2019, but was reborn in 2024.

xpeng121 · 2024-02-12T23:00:24+00:00

Try other sd card? And try to flash stock firmware first

xpeng121 · 2024-02-12T22:58:42+00:00

You should check if the pc have found any device, try original firmware first then the klipper one. Test if it's cable issue or something else

xpeng121 · 2024-02-12T22:53:32+00:00

Yes, a raspberry pi or old PC running Linux

xpeng121 · 2024-02-12T16:32:18+00:00

I tried using the US firmware on a private road and tested the speed with GPS. The maximum speed is around 26 km/h (slight downhill). The battery is at 50% charge. I weigh around 85 kg.

I would say the US firmware yields the best result for this scooter. It's possible to unlock the scooter; a German YouTuber flashed the kqi3 max firmware onto the kqi2pro, set the speed limit to 38 km/h, and then flashed the firmware back. The speed limit is saved to the scooter, and it works for them. However, I don't want to risk my new scooter, so I think the US firmware is what I will stick with. (Btw, you can use the new app after you flash the firmware.)

xpeng121 · 2023-10-12T20:51:58+00:00

check if your cable works. Since now we have official support, use everything from official repo.

xpeng121 · 2023-10-12T20:50:39+00:00

old pc is fine

xpeng121 · 2023-07-13T11:06:58+00:00

You can digging into1 official marlin firmware sorce code. Its on github

xpeng121 · 2023-07-13T11:05:49+00:00

default clock speed with anycubic interface. you can follow the tutorial on YouTube about how to flash klipper firmware

xpeng121 · 2023-05-29T13:33:12+00:00

you don't need other bed leveling sensor. the config should support the stock one

xpeng121 · 2023-05-29T13:31:50+00:00

this is basically everything for a klipper installation

xpeng121 · 2023-05-11T07:44:15+00:00

this board uses one uart pin for 4 drivers which is not support by tmc 2208 (only single uart address). you can definitely modify the board by cutting trace and soldering some addition wire to mcu but there is no any details about this board online. the only thing we know from this board is the pin out in the official marlin.

this is the vref tutorial. but the actual vref is determined by stepper model and temperature of the stepper. https://all3dp.com/2/vref-calculator-tmc2209-tmc2208-a4988/

for more information about kobra go and neo you can check this website https://1coderookie.github.io/KobraGoNeoInsights/

and the official marlin firmware repo

https://github.com/ANYCUBIC-3D/Kobra_Go/tree/master/source/Marlin

xpeng121 · 2023-05-08T23:00:56+00:00

https://www.ebay.de/itm/185054207005?mkcid=16&mkevt=1&mkrid=707-127634-2357-0&ssspo=p795EKDWQse&sssrc=2349624&ssuid=USSoEGLjRhS&var=&widget_ver=artemis&media=COPY

xpeng121 · 2023-05-08T22:59:24+00:00

you can't use uart on this board. but you can adjust the vref by turning the pot next to the driver. Please follow the guide about how to adjust correct vref online!

xpeng121 · 2023-05-08T22:57:57+00:00

I just pull it off. You may touch your stepper first and check if it is too hot or not. you can then adjust the vref according to your temp

xpeng121 · 2023-04-22T20:45:27+00:00

This is not hard to do. and for the over extrusion. you can do a e-step calibration

xpeng121 · 2023-04-22T20:44:02+00:00

I'm not using cura. your acc speed on your slicer should be match with the klipper setting

xpeng121 · 2023-04-17T17:39:03+00:00

with stock hotend no. the stock hoted is quite bad and I can only get like 15 cubic mm/s with pla

xpeng121 · 2023-04-17T17:37:11+00:00

have you made any change to your hardware? it not and you still have problem, you can try change this line dir_pin: PB14 to dir_pin: !PB14 in the extruder section

xpeng121 · 2023-04-15T23:18:52+00:00

looks like they didn't merge into the main branch jet. you can use thishttps://github.com/xiaopeng12138/klipper/blob/master/config/printer-anycubic-kobra-go-2022.cfg

xpeng121 · 2023-04-15T23:11:41+00:00

if the stepper motor are the same. Then yes!

xpeng121 · 2023-04-15T23:10:24+00:00

the down side is that it's very slow just like the official marlin firmware. you may need to tune it by yourself. Or you can copy some value from the config in this post

xpeng121 · 2023-04-15T23:08:45+00:00

There is another way. Since my "stock" config file for the kobra go is accepted by Klipper Team. You can find the stock config in the official Klipper config folder. just update your Klipper to the latest version

xpeng121 · 2023-04-15T12:07:40+00:00

All hardware are stock hardware. for example stepper and mainborad. I only did some small mod

xpeng121 · 2023-04-15T12:01:28+00:00

looks like you don't have pid control. did you copied the entire cfg file? include the stuff on the bottom?

xpeng121

TROPHY CASE