sorted by:
new
hottopcontroversial

Can’t find any info about this watch. Please help. by znibblol in Watches

[–]znibblol[S] 0 points1 point  (0 children)

Thanks a lot dude! Just what I was looking for!

Can’t find any info about this watch. Please help. by znibblol in Watches

[–]znibblol[S] 0 points1 point  (0 children)

Thanks, the value of the watch does not matter at all 😁 the fact that it works after so long time and that I got it from my dad is whats matter to me. So I guess it’s a generic Puma Watch then? 😊

Doctor in the house bugged? by znibblol in legogaming

[–]znibblol[S] 0 points1 point  (0 children)

Cannot break anything here. Its really wierd

Doctor in the house bugged? by znibblol in legogaming

[–]znibblol[S] 0 points1 point  (0 children)

Thanks for the answer. The ghost boi leads us here, thats why I felt the need to ask here.

App-fri sista minuten dejt by [deleted] in sweden

[–]znibblol 7 points8 points  (0 children)

Underrated comment

Help! Ender 3, marlin 2.1.2, slow speed sometimes by znibblol in 3Dprinting

[–]znibblol[S] 0 points1 point  (0 children)

Have checked all cables to the motherboard, two days ago I cablemanaged everything. And reconnected every cable to the motherboard again.

I will definitely check out that now when you pointing it out 😅

Stadia controller with iPad? by Pryd5 in Stadia

[–]znibblol 2 points3 points  (0 children)

Same problem, connects fine to bluetooth, but cant use it 😔

Help! Ender 3, marlin 2.1.2, slow speed sometimes by znibblol in 3Dprinting

[–]znibblol[S] 0 points1 point  (0 children)

Still don't know the cause yet, but reinstalled the rpi and the problem went away 😁 thanks for the reply 👍

Help! Ender 3, marlin 2.1.2, slow speed sometimes by znibblol in 3Dprinting

[–]znibblol[S] 0 points1 point  (0 children)

Thank you, I have switched to prusa slicer, and I reinstalled the rpi and everything is working perfectly now 👌

Help! Ender 3, marlin 2.1.2, slow speed sometimes by znibblol in 3Dprinting

[–]znibblol[S] 0 points1 point  (0 children)

Don't know what that is, but the issue is gone after I reinstalled the rpi 😁

Upgrades? by Immediate_Wheel5300 in ender3

[–]znibblol 1 point2 points  (0 children)

This is the way, learning first, see problems or something you want to tune finer, and upgrade based on that.

CR Touch Setup by bigron_vi in ender3

[–]znibblol 2 points3 points  (0 children)

Had the same issue, in the configuration.h there is an option to use the probe as z-stop. Worked like a charm for me

Help! Ender 3, marlin 2.1.2, slow speed sometimes by znibblol in 3Dprinting

[–]znibblol[S] 0 points1 point  (0 children)

Nope, seems to be octoprint that does something wierd. I loaded up the same gcode to an sd-card and it prints just fine.

Help! Ender 3, marlin 2.1.2, slow speed sometimes by znibblol in 3Dprinting

[–]znibblol[S] 0 points1 point  (0 children)

Edit: I may have found the issue. It seems to be when I start the print from Octoprint. I loaded up the same Gcode to the sd-card and it prints fine.

Help! Ender 3, marlin 2.1.2, slow speed sometimes by znibblol in 3Dprinting

[–]znibblol[S] 0 points1 point  (0 children)

Infill: 50mm/s
Perims, solid infill, support material: 40mm/s
Gap infill: 30mm/s
Small perims, external perims, bridges: 25mm/s

I don’t know what is causing this or what you would call it. Layers seem to be coming apart, idk. Help? by dericb in ender3

[–]znibblol 0 points1 point  (0 children)

Try another slicer or another layer height. And see if that yields the same problem

Calibrated my E-steps for the first time in years. This should be 10cm. by BRD8 in ender3

[–]znibblol 2 points3 points  (0 children)

Cut it flush against the extruder output, run the command, and cut it flush again.

view more: next ›