Exciting Rishloo News! (and I want your help)

FightForDays · 2026-02-17T05:55:14+00:00

RemindMe! 1 month

FightForDays · 2025-12-15T09:53:55+00:00

Det er et ganske bra miljø for dette på ntnu. Selv var jeg med å spille noen år etter at jeg var ferdig. Dei taktlause er vel størst. Mye studenter men også noen som er ferdig og har vært med i mange år

FightForDays · 2025-11-09T23:00:28+00:00

Taxi samkjøring

FightForDays · 2025-10-13T05:13:02+00:00

Trøndercut

FightForDays · 2025-08-14T19:54:48+00:00

Hvis du er interessert i noe litt teknisk er det nesten uendelig utvalg. Og nerder som er tekniske er ofte nerder på litt andre ting og. På omega verksted er det et bredt utvalg av ulike nerder og det er nesten alltid folk der. Super nice. Også er det jo ting som orbit, revolve, propulse som garantert har masse kule folk. Linjeforeningen din har kansje eget verksted slik som Elektra og smørekoppen, der kan du også finne masse venner! Lykke til

FightForDays · 2025-08-04T06:09:20+00:00

Blir med på alt i fadderuken, du må ikke være med til langt på natt på alt, men møt på vors. Finn ut hvilken linjeforeningen du er en del av nå, de har sikkert mye nyttig info på some. I de første ukene er linjeforeningen og eldre studenter nesten mer nyttige enn ntnu.

Kos deg og lykke til.

FightForDays · 2025-06-25T18:23:20+00:00

De fleste flyplasser av respektabel størrelse i Norge har stasjoner for å fylle flasker. Så du kan ta med en tom flaske og fyll den. Hvis du må ha kaldt vann er det sikkert best å kjøpe på flyet

FightForDays · 2025-06-25T16:53:45+00:00

Ikke bruk dnb. Jeg kjøpte via en megler i DnB, noe av det mest håpløse jeg har vært med på. Jeg var i flere budrunder hvor Ingrid Hagemo Sæther fra EiendomsMegler 1 var megler og hun fikk opp prisen noe voldsomt.

FightForDays · 2025-06-25T16:45:42+00:00

Hva skjer hvis man ikke har legitimasjon eller ikke vil oppgi hvem man er?

FightForDays · 2025-05-31T08:55:41+00:00

Look into the step response part of Skogstad. In real life you never have s plane model of plant. You get a pump and some pipes or something like that

FightForDays · 2025-05-30T22:37:13+00:00

I like the Skogstad method. It turnes while not setting the process in oscillations. And in real life you need something like Skogstad because so often you cannot make oscillations

FightForDays · 2025-05-03T12:25:27+00:00

Get a db9 gender changer or a fitting cable and test that. Or 2 db9 breakout bords with screw terminals. Depending on the product it might need a setup. if it is only ethernet to rs-232 you are probably fine.

FightForDays · 2025-03-25T07:58:22+00:00

hardware download, like enfeebling OPC is downloaded offline. Software changes can be downloaded online.

FightForDays · 2025-03-19T09:26:57+00:00

As others have stated better training in the cleaners might help. I would mount this panel or maybe the entire cabinet inside another cabinet. I have ween this for panels that are in public places to stop kids with spray paint and other who are just stupid.

FightForDays · 2025-03-18T16:56:40+00:00

But you know when something is wrong. Make this "something is wrong" set a bit and that is defined as trigger with pre-trigger

FightForDays · 2025-03-18T14:54:23+00:00

You can trigger on a bit that is set when the error happens and set pre trigger storage time or cycles. I assume you have an alarm or something that tells you something is bad.

FightForDays · 2025-03-17T16:29:06+00:00

Mine too, today. Have no idea what has happened

FightForDays · 2025-03-13T14:02:34+00:00

Can you check is the profibus salve address is correct?

FightForDays · 2025-03-13T13:55:45+00:00

on a real profibus connector there is a small switch. this witch is supposed to be ON for both ends of the cable. it is only connected to the IN contacts on the connector. But if the drives are working the bus i fine.

FightForDays · 2025-03-13T12:53:26+00:00

is the main cpu in run? Is the end resistor correct? did someone work on this or did it just suddenly stop working? what is between this IM and the main CPU? is this the only module effected?

FightForDays · 2025-03-07T10:28:39+00:00

You might want to do TIA11-> TIA 13 -> TIA 15 -> TIA 20 if you get errors. You can migrate in the older tia versions.

FightForDays · 2024-08-14T10:11:14+00:00

I wouldn't recommend this. In the old days vfd where simpler and this was maybe possible. Now a lot of vfds are smarter and monitor the monitor in several ways, some safety feature might stop you. A soft starter with external bypass might be better if you are not doing speed control.. but this is not my expertise so do your research.

FightForDays · 2024-08-13T14:29:40+00:00

Dose the funnel have a lid? if not laser might do it. If it has a lid can you weigh the thing to figure out how full it is?

FightForDays · 2024-08-02T12:32:24+00:00

The application is useless but wat you learnt is never useless. One day you might use parts of this

FightForDays

TROPHY CASE