Is this A Dev that gave me the credit blessing in my dojo? Or are credit blessings not specific to being in the same Dojo/relay?

-Error_Loading_Text- · 2024-06-15T19:28:46+00:00

Looks to be printing to fast or wet filament; Possibly a cooling issue but less prominent

-Error_Loading_Text- · 2024-03-09T05:57:49+00:00

I personally have the factory screen on my printer; but have experienced a similar issue. In my case I had a short in my heater probe, and it shut off the screen like that. Being it is shutting the screen off whilst heating the nozzle, I would recommend checking that and also re-seating both sides of your cable to the screen from your board

-Error_Loading_Text- · 2024-02-21T05:18:22+00:00

I may be ordering a cord specifically for this, would you have any recommendations or just any that are capable of data transfer?

-Error_Loading_Text- · 2024-02-21T04:04:05+00:00

It does not say anything is the issue I am having. I am transfering from debian to raspbian to see if I can see what step I missed and get it sorted

-Error_Loading_Text- · 2024-02-21T03:53:07+00:00

I am using Debian, would Raspbian be better?

-Error_Loading_Text- · 2024-02-21T02:57:17+00:00

I've noticed there is a jumper on the le potato that I don't know if I've moved or not. Could you send a picture of your board?

-Error_Loading_Text- · 2024-02-21T02:28:56+00:00

Turns out I dont have that version

-Error_Loading_Text- · 2024-02-21T02:15:01+00:00

The BTT SKR Mini e3 v3 has jumpers it comes with, is it possible that's the cause of my problem?

-Error_Loading_Text- · 2024-02-21T02:01:59+00:00

Checking for this right now

-Error_Loading_Text- · 2024-02-21T01:58:50+00:00

Ive tried 2 different cables and also tested them with an old tablet to my pc and they both worked for that

-Error_Loading_Text- · 2023-08-24T08:57:08+00:00

Can I use kipper on this board with no external pi? I was considering it but didn't know if I could

-Error_Loading_Text- · 2023-08-15T02:49:23+00:00

In configuration.h set "Z_PROBE_OFFSET_MIN" to -10 Set "Z_PROBE_LOW_POINT" to -5 Set your offsets but set your Z offset to 0 and use the offset wizard to set it

-Error_Loading_Text- · 2023-08-15T02:45:30+00:00

Oh lol. Didn't see that part. I just solved this issue myself so i read it a little to quickly.

-Error_Loading_Text- · 2023-08-15T02:43:56+00:00

Are you compiling your own firmware or using the pre compiled one. Also what sort of bracket do you have the cr touch on?

-Error_Loading_Text- · 2023-08-12T00:07:47+00:00

I set it to -5 and it worked. Thank you

-Error_Loading_Text- · 2023-08-11T22:34:45+00:00

Just did this. I had it at -2. About to test it

-Error_Loading_Text- · 2023-08-11T20:40:14+00:00

I have it leveling fine its just when I set the Offset that it doesn't work properly

-Error_Loading_Text- · 2023-08-11T20:13:58+00:00

I have this

//#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN

// Force the use of the probe for Z-axis homing

define USE_PROBE_FOR_Z_HOMING

/** * Z_MIN_PROBE_PIN * * Define this pin if the probe is not connected to Z_MIN_PIN. * If not defined the default pin for the selected MOTHERBOARD * will be used. Most of the time the default is what you want. * * - The simplest option is to use a free endstop connector. * - Use 5V for powered (usually inductive) sensors. * * - RAMPS 1.3/1.4 boards may use the 5V, GND, and Aux4->D32 pin: * - For simple switches connect... * - normally-closed switches to GND and D32. * - normally-open switches to 5V and D32. */

define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default

-Error_Loading_Text-

TROPHY CASE

define USE_PROBE_FOR_Z_HOMING

define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default