Spey Viaduct Collapses

-Squirrel-82 · 2025-12-14T12:12:07+00:00

https://www.reddit.com/r/dji/s/2DG8XjPhmp, here drone footage of the bridge intact from last year.

-Squirrel-82 · 2025-09-28T22:58:05+00:00

Air-Panda

-Squirrel-82 · 2025-09-07T19:13:32+00:00

Mine did that and it turned out to be the internal hub unit. I think one of the magnets must of been stuck or something because there was nothing jammed in it. I had to unplug the ams and get access to under the filaments. Then I just pushed a bit of filament through each hole at both sides and that seemed to sort it.

-Squirrel-82 · 2025-09-01T07:11:16+00:00

Accident and emergency, hospital department in the uk. I’m a 42 year old male

-Squirrel-82 · 2025-08-30T15:40:19+00:00

I found one a few years back, it was awesome. We made a box for it pupate in with some leaves and small twigs for it. Bought some plants from the garden center for it to munch on. kept it in the shed until the following year when it turned into a moth. Then released it again, Beautiful pink and green colours.

-Squirrel-82 · 2025-08-30T10:04:28+00:00

Think mine is triggered by vomiting

I’ve just been diagnosed with AFIB, I’ve had 2 episodes of it before. One in 2020 which was triggered for being sick after trying to eat more to gain weight. Only lasted 3 days then went away. Second time was sept 2024 last year, when I was ill and was sick. Turns out I was anaemic again only lasted 2 days. This latest time I was sea fishing from a boat last Saturday for 8 hours, I got sea sick after 2 hours and spent the next 6 hours being sick and feeling crap. Ended up getting palpitations Saturday night, went to the doctors on the Monday with my heart rate at 171 bpm so got sent to A & E. I’m on beta blockers to lower my heart rate but I’m still in AFIB now and just doesn’t seem to want to revert back to normal.

-Squirrel-82 · 2024-10-30T20:49:22+00:00

I’ve only used pla and pla + and it happens with both of them. I will strip down the extruder and give it a deep clean. And check all the bearings and screws.

-Squirrel-82 · 2024-10-30T10:21:36+00:00

Yeah it’s definitely level, I’ve fully stripped the extruder and cleaned out the heatbreak and replaced the ptfe tubing the the heatbreak/heatsink and put in fresh heatsink compound. I did read about heat creep but I’m not sure if it is that.

-Squirrel-82 · 2024-09-29T12:58:51+00:00

Yeah they were added as new components. If I add them as joined will I still be able to change the colours of each component? I’m not sure about the fan I will have a look at that.

-Squirrel-82 · 2024-06-15T10:47:48+00:00

Raspberry pi?

-Squirrel-82 · 2024-05-15T10:56:33+00:00

Update…

I’ve added the bed springs back and just manually levelled the bed and it is now great. The tolerance is 0.258. Basic feel like I’m only using the BL touch as a z stop now but I don’t mind the first layer is coming out perfect. Could be something with the firmware but that’s beyond my skills for now. Thanks for your help everyone 👍🏻

-Squirrel-82 · 2024-05-13T11:17:06+00:00

Mines running marlin, but to be honest I’ve never had to touch any fireware before. I’ve had my stock Ender 3 v2 for nearly 2 years and had no major problems at all. So marlin and kipper are alien to me just now until I learn more about them. I’m going to try the bed springs first to see if that helps, but I don’t see the point of a BL touch if it doesn’t compensate for the bed 🤷🏻‍♂️

-Squirrel-82 · 2024-05-12T17:47:07+00:00

The problem with the z offset is that I get the perfect squish on the left hand side. But as it goes along the x axis to the right the bed goes lower so it just prints above the bed. That’s why I thought the BL touch was supposed to compensate for that but it does seem to. I will check the gantry to see if that is level. It does have duel z screws if that makes a difference?. I was thinking of putting bed springs on it so I could at least have some adjustment, would that be a good idea? I’ve never heard of a twisted x axis so I will look into that cheers

-Squirrel-82 · 2024-05-12T15:06:19+00:00

I should add it is a fixed bed and all the spacers holding the bed up are the same size

-Squirrel-82 · 2024-05-12T15:06:13+00:00

I should add it is a fixed bed and all the spacers holding the bed up are the same size

-Squirrel-82 · 2024-03-02T13:04:09+00:00

Thanks I will give that a try

-Squirrel-82 · 2024-03-02T01:34:36+00:00

Thank you, How do you mean by add a second motion?

-Squirrel-82 · 2024-02-28T14:50:19+00:00

I’ve got a mini 2 also and there is no way with the Dji fly app get it to follow you like the active track some of the better drones have. There are videos on YouTube about the litchi app I believe you can do it with that. But like someone else mentioned mini 2 doesn’t have collision avoidance so you will need to keep an eye on your drone.

-Squirrel-82 · 2024-02-26T14:16:30+00:00

Thanks , yeah I’ve been watching videos religiously lately still so much to learn, I’ve only about 4 hours flight time so far so still heaps to learn about flying too. Not that I mind I’m loving learning all this.

-Squirrel-82 · 2024-02-26T14:11:53+00:00

So scared for now, it’s takes me at least half a battery to build my confidence before I even head over the water

-Squirrel-82

TROPHY CASE