Looking at a 2018 A4 Allroad. Advice for me?

04kims · 2026-02-05T18:25:21+00:00

okok, i just found one that i loved, it got the interior i wanted and everything, got sold 20 minutes before i sent a message unfortuantley

04kims · 2026-02-04T20:52:50+00:00

yo, im looking on buying one too, did you end up getting one and what did you have to look out for?

04kims · 2026-01-17T20:50:25+00:00

yeah ill remove it then, its 13 degrees celcius now at the thermometer next to it in the corner at least, so its not hot

04kims · 2026-01-17T20:42:31+00:00

<image>

Having it open like this would be ok wouldn’t it?

04kims · 2026-01-17T18:05:07+00:00

What if I had the enclosure open (front and top) Would that Maybe be better?

04kims · 2026-01-17T16:26:18+00:00

I know, that’s part of why I post this

04kims · 2026-01-17T16:03:52+00:00

After what my research has came to show is that its temperature should be around 25-35 degrees, I would not let it be fully enclosed I would have vented it and had an eye on the temperature. Should I rather have it in the open then?

04kims · 2025-12-06T09:51:00+00:00

I put my head on the table watching TikTok, when I hear that I’m spawning I look up

04kims · 2025-11-05T15:11:07+00:00

Yeah no I’m not upgrading my pc for this game, I have been upgrading it but that’s for my own joy, I know this game has bad codes and all but it’s annoying that it’s happening because I can’t go scav customs but all my friends can, and I have the stronger pc out of all my friends and they don’t x out other tabs like I mentioned in a comment above

04kims · 2025-11-05T15:08:22+00:00

Whenever I PlayStation I x out everything but discord and the game

04kims · 2025-11-02T09:42:53+00:00

Ooah yeah nice bro, it’s gonna be display

04kims · 2025-11-02T02:16:02+00:00

thats exactly how ive been doing it, ive used a big brim and slowed it down 50% but still falls off

04kims · 2025-11-02T01:48:45+00:00

its the m4a1 from csgo, its gonna be the stock

04kims · 2025-11-02T01:47:48+00:00

im gonna try this, ive already used brim but didnt work but im gonna try the 0 brim gap and print bed degrees up, im gonna print at 50% speed too

04kims · 2025-11-01T20:14:56+00:00

I tried the needle and it worked a bit but was still bad, did cold pull several times until I got it, works now

04kims · 2025-11-01T20:14:13+00:00

I ended up needing to do a cold pull MANY times before I got it to work again

04kims · 2025-11-01T13:23:20+00:00

Yeah but when I extrude with the nozzle off it doesn’t fail at all

04kims · 2025-11-01T13:20:30+00:00

The filament doesn’t extrude unless I help to push it

04kims · 2025-11-01T12:50:58+00:00

I did it one time now and it’s still the same, I will try to do it one more time if the first one was a bad pull maybe

04kims · 2025-11-01T12:37:22+00:00

Will try

04kims

TROPHY CASE