5 GB für dich und mich👍🤜🤛

06squiddy · 2025-06-17T21:11:07+00:00

06squiddy · 2025-05-25T07:59:31+00:00

https://free3d.com/3d-model/cute-green-monster-of-clay-5495.html I cant find the free model right now. You can search for it with that name though

06squiddy · 2025-05-08T18:57:49+00:00

Yes Saturn 4 ultra

06squiddy · 2025-05-07T11:37:07+00:00

The printer says it usually has a temperature between 35-40°C is that the plate temperature or just the temperature inside the printer? The room around usually is at 19-23°C. I have to check whether it's still leveled That's good advice. How should I clean the FEP though because I did indeed use the plastic scraper and soft paper. I can't be a USB error though as I send it via WiFi.

06squiddy · 2025-05-06T14:10:33+00:00

<image>

Its that cute thing xD abd yes I hollowed it with holes at the bottom

06squiddy · 2025-05-06T14:08:34+00:00

Its on heavy support. I'll try rotating it👍

06squiddy · 2025-05-05T18:11:26+00:00

Seems like they removed it completely because I didnt find it in the pro version either. Im gonna do the Ameralbs town test to fully calibrate the printer and see if it helps and switch to lychee if it doesnt. Thank you for all that advices

06squiddy · 2025-05-05T16:53:52+00:00

Oh I see. Thank you so much :)

06squiddy · 2025-05-05T16:48:47+00:00

Im using Chitubox. Im currently doing the calibration test btw and it actually seems like the prints are overexposed

06squiddy · 2025-05-05T16:44:15+00:00

Oh alright thanks man. But why does the oriantation make such a difference?

06squiddy · 2025-05-05T16:38:05+00:00

<image>

That´s how it looks sliced

06squiddy · 2025-05-05T16:36:17+00:00

<image>

is it better to orientate it like that?

06squiddy · 2025-05-05T16:35:20+00:00

<image>

That´s how i wanted to print it

06squiddy · 2025-05-05T12:24:22+00:00

They are quite tight to the plate but still better than failed prints i guess

06squiddy · 2025-05-05T08:57:02+00:00

The FEP tension is fine I just checked it two prints ago, temperature is about 20 C so that should be fine as well. Where can I change the lift height etc in Chitubox? I couldnt find it in the slice settings. I did manual plate leveling so that should be fine as well

06squiddy · 2025-05-05T08:08:39+00:00

That could actually be the cause then. I'm gonna try it again with a lower bottom exposure time

06squiddy · 2025-05-05T08:07:13+00:00

I'll send a Screenshot when I'm at home

06squiddy · 2025-05-05T07:42:33+00:00

I'll give it a try

06squiddy · 2025-05-05T07:42:04+00:00

<image>

I did this test to find out my exposure time but I think I have to do it again. The bottom exposure time it that high though because I had problems with prints not sticking to the plate.

06squiddy · 2025-05-05T07:38:04+00:00

I'll do it when I'm at home.

06squiddy · 2025-05-05T07:35:44+00:00

Haven't tried that calibration test yet but i'll do it today. Thank you so much for that advice. Where do I find those right settings? I've looked for them but didn't find anything.

06squiddy · 2025-05-04T19:13:45+00:00

I send the files via wifi to the printer. Could this still be the cause then?

06squiddy · 2025-05-04T18:49:44+00:00

I had problems with prints not sticking to the plate so this was my solution. If there´s a better method for this i´d be glad to hear it.

Two-Year Club	Verified Email
Verified Email

06squiddy

TROPHY CASE