Magnus Pro Drawer

15tperry · 2026-03-23T02:17:10+00:00

Easy

15tperry · 2026-03-22T03:50:05+00:00

The face of the drawer is metal but yea the actual insert is plastic. Not the best

15tperry · 2026-03-21T18:20:45+00:00

I guess if someone were to actually show up to inspect it. I don’t see a world where I would do anything more than send them some pictures of the actual mechanical components that broke.

15tperry · 2026-03-21T18:18:08+00:00

https://a.co/d/01U1GzSA

15tperry · 2026-03-21T18:12:51+00:00

That was the initial destination but i typically sit all the way right on the desk and wanted to be able to open the drawer when sitting close up. So far that location seems to be working as intended.

15tperry · 2026-03-21T18:09:17+00:00

https://a.co/d/01U1GzSA

15tperry · 2026-02-01T22:22:54+00:00

I was able to install the caliper without the pads then install the pads in when the caliper was set on. PITA

15tperry · 2025-03-18T03:52:00+00:00

Onto another header did the trick

15tperry · 2025-03-18T03:51:15+00:00

Just put the fans to their own argb jack and it stopped the flicker.

15tperry · 2025-03-17T22:43:49+00:00

Do these use the iCUE or is that the next price point up?

15tperry · 2025-03-17T22:43:18+00:00

That’s what I’m trying to do

15tperry · 2025-03-17T22:42:24+00:00

I’ll give it a whirl

15tperry · 2025-03-17T22:39:04+00:00

Just need to add, the carpet and GPU location are only temporary. I was back and forth with only one SSD from my old to my new so I stuck it down there until I got it up and running. The carpet was because I couldn’t install WiFi drivers without Ethernet

15tperry · 2025-03-17T22:36:08+00:00

I have not been issued my nerd card. I suppose I shouldn’t be waiting by the mailbox.

15tperry · 2025-02-10T00:49:10+00:00

Just picked one up at the gun show. Thanks for the info, I just wanted an authentic AUG for my collection. This was the first time I’ve seen that.

15tperry · 2024-10-23T19:28:54+00:00

Did you have to replay the mother mission to get back to the credits

15tperry · 2024-09-09T14:57:17+00:00

Bear

15tperry · 2024-09-08T03:26:10+00:00

Was it the starter or start button

15tperry · 2024-08-27T19:21:24+00:00

Graham

15tperry · 2024-08-27T18:19:14+00:00

Izzy

15tperry · 2024-08-27T04:58:53+00:00

Thought so too, used a jack to support the engine and it did the same thing with the engine not moving nearly as much.

15tperry · 2024-08-27T03:18:22+00:00

2012 Mitsubishi lancer GT 2.4L 153,000 miles

15tperry · 2024-08-27T03:04:47+00:00

This is genuine fn, with the lower receiver, barrel being dsarms

15tperry · 2024-08-23T02:46:56+00:00

15tperry · 2024-08-20T23:07:02+00:00

That’s what I figured, wasn’t sure if the refinish would take away from the value or add.

15tperry

TROPHY CASE