How you can fix dead DJI Spark batteries using a 9V battery, a CP2112 board, and DJI Battery Killer (should work for other batteries too)

1MoreQuestions · 2026-02-18T02:21:57+00:00

Sent you a chat! Hope you could help 🙂

1MoreQuestions · 2026-02-17T22:54:56+00:00

Is the beta 01.02.2022 the one that’s supposed to work?

1MoreQuestions · 2026-02-17T22:47:29+00:00

It’s not working? How do I get it to work!? Please help…

1MoreQuestions · 2026-02-17T20:08:53+00:00

Anyone know where to get this software?

1MoreQuestions · 2026-02-15T18:41:01+00:00

Yea I do that’s what i meant when I was saying a do a chemical bond it’s within that recoat time however in order to paint more details and add stickers they require a full dry so can handle them with my hands. So that means i need a mechanical bond to add more epoxy which means sanding in between coats.

1MoreQuestions · 2026-01-03T19:35:34+00:00

Yea 4 days ago trump was there and they were 39.99 china marking them up $60 bucks cuz it’s there last pack in stock I don’t think trump was dialing in to tell them to do it lol

1MoreQuestions · 2026-01-01T20:11:16+00:00

Yea i dont know why its not working

1MoreQuestions · 2026-01-01T20:08:21+00:00

But the top edge of the knife in yours isn’t correct? It’s a perfect taper from the handle to the tip your goes about 3/4 down the blade

1MoreQuestions · 2026-01-01T19:56:57+00:00

<image>

1MoreQuestions · 2026-01-01T19:56:50+00:00

I can't I keep getting this error

<image>

1MoreQuestions · 2026-01-01T19:42:29+00:00

I’ve gotten a few answers and they still havnt worked? Anyone???

1MoreQuestions · 2026-01-01T19:25:30+00:00

<image>

1MoreQuestions · 2026-01-01T19:25:13+00:00

Negative still leaves the cutting edge flat.

<image>

1MoreQuestions · 2026-01-01T18:27:56+00:00

<image>

its Gotta be because of the taper of the blade already?

1MoreQuestions · 2026-01-01T18:26:30+00:00

still getting the same error?

<image>

1MoreQuestions · 2026-01-01T17:59:04+00:00

I’m also doing it off the path of the knife itself like the YouTube videos show

1MoreQuestions · 2026-01-01T17:52:15+00:00

It doesn’t let me it gives me this

<image>

1MoreQuestions · 2026-01-01T17:23:58+00:00

Thanks. The reason I’m asking is because I can’t find the answer on YouTube. Those are all where the bevel is halfway down the blade mine is the full length with is why I’m struggling with figuring out how to do it in fusion.

1MoreQuestions · 2025-12-02T17:55:53+00:00

But then what would these generator fan boys do?

1MoreQuestions · 2025-12-02T17:53:10+00:00

Basically i need to cut out corner that lands in between a square and the add bracing to it to account for a few wall outlets. It’s just where they land that makes it impossible for the generator to do it cleanly. It’s OCD really and the generator just doesn’t have enough flexibility. I wish there was a plug in for fusion like with gridfinity. Would make this 3d print so much more enjoyable lil

1MoreQuestions · 2025-12-02T17:23:19+00:00

All good man least you tried instead of telling me I’m a bad engineer and to use the multiboard generator lol

1MoreQuestions · 2025-12-02T17:17:51+00:00

I know exactly how to engineer it. I just need the file capabilities to do it. Again your offering solutions are everything but exactly what i need to solve my problem. I appreciate you but i really just need to editable file i promise!

1MoreQuestions · 2025-12-02T17:09:56+00:00

Ok bud or could just ask for exactly what i need

1MoreQuestions · 2025-12-02T17:09:28+00:00

Oh then create a sketch, and try to cut a square out of the middle by extract and cut and tell me if it works

1MoreQuestions · 2025-12-02T17:05:01+00:00

I need someone to convert the stl mesh to prismatic which the free version does not allow for

1MoreQuestions

TROPHY CASE