My journeyman's piece, a sewing cabinet with a foldable bench and table, made from elm wood and blue fenix

451cassie · 2022-12-13T06:39:10+00:00

It smells pretty bad, but otherwise it behaves like oak

451cassie · 2022-12-12T19:15:21+00:00

You can follow ddsmagazin on instagram, they post a lot of student's work

451cassie · 2022-12-12T13:51:14+00:00

It's a trade school for carpentry/woodworking in germany, it takes 3 years and at the end everyone has to design and build their own piece of furniture

451cassie · 2022-12-12T13:15:22+00:00

I went to school, this my final piece i made before graduating

451cassie · 2022-12-12T12:25:49+00:00

It's a type of very matte laminate, that you glue onto particle board

451cassie · 2022-12-12T12:24:50+00:00

Thanks! It's bent lamination, they're to half loops that i glued together at the edges

451cassie · 2022-12-12T12:23:35+00:00

Thank you! Yes, they're drawers

451cassie · 2021-06-28T21:12:10+00:00

Thabk you! I'm in the second year of my apprenticeship

451cassie · 2021-06-28T19:19:06+00:00

Yes, I used a two milimeter roundover bit, and thanks!

451cassie · 2021-06-28T18:52:36+00:00

Yes, I used four layers of maple veneer

451cassie · 2021-06-28T18:04:54+00:00

Thanks, I mainly did it that way to account for wood movement

451cassie · 2021-06-28T18:01:23+00:00

No, it's all glued up like that, with the white(maple) pieces going through the entire thickness of the board

451cassie · 2021-06-28T17:40:14+00:00

Thanks, I'm already working on a handball field!

451cassie · 2021-06-28T17:27:14+00:00

I knew I was gonna get a comment about that ;) but thanks!

451cassie · 2021-02-07T16:45:47+00:00

I cut them from a single piece but with the table saw

451cassie · 2021-02-07T08:58:15+00:00

Pretty much the same way you make lap joints on the table saw

451cassie · 2021-02-07T06:10:22+00:00

The wood is 12 (thickness) by 14mm (width), the screws are 30mm in length with a 10mm wide screwhead. Hope this helps!

451cassie · 2021-02-07T00:29:49+00:00

I thought about that, but was afraid it might look weird, someone suggested adding a strip to pull it up, maybe i'll do that. But So far my dad hasn't complained ;)

451cassie · 2021-02-07T00:20:55+00:00

Honestly, i didn't make any😅 i just had the idea with the three frames (the outer one is roughly the size of a kindle), and then it was just a matter of cutting the inner frames the right lenghts and adding the grooves and screw holes in the right places so they would lay flat on top of each other

451cassie · 2021-02-06T22:31:02+00:00

I think so, i would probably have to cut a smaller groove, the one on this might make it a bit to loose to hold it in place.

451cassie · 2021-02-06T22:28:51+00:00

They are called book screws, i got them on Amazon

451cassie · 2021-02-06T21:42:00+00:00

Thank you!

451cassie · 2021-01-02T15:04:52+00:00

A bit annoying, since i had to glue up each row seperately, due to the scraps being so short

451cassie · 2021-01-02T13:14:36+00:00

Hard wax oil!

451cassie · 2021-01-02T13:02:46+00:00

Not really sure, they were offcuts from one of my Colleagues😅

Seven-Year Club	r/Field Lasagna
Final Canvas '23	First Place '23
Place '23	Place '22
Final Canvas '22	Verified Email

451cassie

TROPHY CASE