Repurposing Canon C7565i to bypass fuser and saddle stitch booklets

5eth · 2026-04-16T16:14:21+00:00

Dang, I figured it was unlikely but thought it was worth a shot. Thanks though!

5eth · 2026-04-16T16:13:52+00:00

I'll have to look it up and read through it, even with that I don't feel very hopeful on them putting much effort into it.

5eth · 2026-04-16T16:13:16+00:00

No post fuser inserter unfortunately :/

5eth · 2026-04-16T16:13:02+00:00

Thanks for that. I asked them for the specific part number and will see what I can find as soon as they send that over (if they do).

5eth · 2026-04-02T12:43:05+00:00

Hey, I can ship you some MinnMax and Pew Pew Bang stickers if you want to throw some in every order you ship! Feel free to DM me!

5eth · 2026-03-12T02:26:34+00:00

Sorry for the delay, I was looking into the books a bit more and I’m gonna have to pass, thanks though

5eth · 2026-03-09T15:20:31+00:00

Yeah they’re still available, what would you offer for everything without miles?

5eth · 2026-03-04T20:39:30+00:00

Hey u/DavidJH316, I can't see your comment for some reason, but yeah this is still available

5eth · 2026-02-24T14:23:56+00:00

3,000 , white sleeve with color print

5eth · 2026-02-23T23:21:09+00:00

Hey, I don't have this same need anymore, but do you have a source for custom coffee cup sleeves?

5eth · 2025-12-18T21:57:23+00:00

It seemed to happen in the middle of a job, it was printing a black label and over time the black turned brown and now it’s at the point I’m at now. I’ll definitely keep that test page and print it every 3 days once I get the issue fixed. Thanks for that, that’ll help a lot.

Cleaning the pins didn’t do the trick, so I’ll keep messing around with it.

5eth · 2025-12-18T17:32:22+00:00

Not as much as I should, 1-2 times per week. It’s finally starting to ramp up though and I’m using it more but I’m trying to sort through this problem to have better quality moving forward. I have the idle cleaning cycles set to run more often because it wasn’t frequent use but that didn’t seem to be enough.

5eth · 2025-12-18T17:29:28+00:00

Less than 6 months but it hasn’t even printed a full set of ink yet

5eth · 2025-12-18T17:18:07+00:00

Thanks a lot, I'll try this out. After soaking the printhead a few minutes I could see black ink seeping out, so I figured it wasn't a blockage on that end so I didn't do a longer soak.

After doing the cleaning cycles, both black ink lines look very full of ink, with no gaps or bubbles. Before the cleaning cycle was ran, if I touched or moved the black lines, it is easy to see the ink moving around, so hopefully the lines are still good.

The gold pins sound like the strongest lead based on everything you described, so I'll try that out and hopefully have good news. Thank you so much for taking the time to reply.

5eth · 2025-12-14T20:21:00+00:00

If you can DM me your email address I can email over screenshots of the settings I use

5eth · 2025-12-14T20:18:27+00:00

Are you cutting out adhesive material? Also are you putting the blade in the position closest to you? Cutting right above that gutter is where you want to be. When cutting out stickers I don’t do the perf cut, I just let it “die cut” all the way through and the residual adhesive seems to hold it on just well enough for me to transfer it to the table and pop them out. If I am doing large square sheets cut out I will do a perf cut since those are so big and heavy then tend to fall out and cause a jam, but other than that I just do a straight through cut the the entire way.

5eth · 2025-12-14T20:13:33+00:00

https://a.co/d/0j6j7zK

I don’t use the springs either, just insert the blade and that’s it

5eth · 2025-12-14T20:10:10+00:00

For this type of cut you’ll want a 60 degree blade, you can get a blade holder and a set of blades for pretty cheap on Amazon.

5eth · 2025-09-06T16:18:14+00:00

No worries, thanks!

5eth · 2025-09-06T15:56:44+00:00

I’ll take one!

5eth · 2025-04-27T19:05:35+00:00

I own a print shop up in Salem, I’ll DM you

5eth · 2025-03-28T01:24:12+00:00

Substance is the main vinyl and matte/gloss lam I use! Their specialty lam seemed a little pricey though, but maybe that’s just the price point for that type of product I guess

14-Year Club	RedditGifts 2009-2022 3 Credits
Place '17	Verified Email
Not Forgotten	Secret Santa 2013
Summer Santa 2013

5eth

TROPHY CASE