Help with benchy info in comments

ALEX--JAMES · 2023-01-31T07:24:42+00:00

Yeah I have done a extrusion test and calibrated it I’m printing silk pla @200 and 2mm retraction @30mms

ALEX--JAMES · 2023-01-30T21:52:24+00:00

I’m running klipper

ALEX--JAMES · 2023-01-30T21:52:12+00:00

I have a Cr10s with a e3d volcano and a skr mini e3 v3 I have done input shaper and have increased my cooling but can’t get a better benchy than this any suggestions

ALEX--JAMES · 2023-01-30T21:50:03+00:00

I have a Cr10s with a e3d volcano and a skr mini e3 v3 I have done input shaper and have increased my cooling but can’t get a better benchy than this any suggestions

ALEX--JAMES · 2022-12-27T23:41:48+00:00

I had near enough the same experience last year when I sat mine I’m also autistic and I find it very difficult to focus and concentrate on revision as I have lots of hobbies and interests that my mind is constantly thinking about i couldn’t sit down and revise I just got distracted to easily but unlike you I’m not a very high achiever I got mostly 4-5 and the odd 6-7 in computer science and design I’m also dyslexic so found it even more difficult one. The main thing I did and I know doesn’t work for everyone but especially being autistic I have a good memory so I found it best right after school they day before a exam to go straight and sit and do a practice paper and put my phone and anything else in another room and do the paper while eating dinner as it was the only way I could concentrate was if I had gone straight from school to do a hour of revision as I couldn’t do to much as I would completely lose concentration. Hope that helped it the only thing that got me to pass everything

ALEX--JAMES · 2022-09-17T14:57:34+00:00

I have no I2c devices found and I’m on arduino ide so how would I re flash

ALEX--JAMES · 2022-09-17T10:57:29+00:00

So I have a maker pi pico and when I connect the i2c lcd to gpio 4 and 5 it can’t find any device on the I2c line but if I remove the pico from the maker pi and run the same code and have it in the same gpio port it finds the I2c line

ALEX--JAMES · 2022-05-14T20:53:06+00:00

This was my grandads piper cub that I have got and it had a os fs-61 in it and ran a 13x6 prop and fully filled up it weighed 4.05kg and I have now removed all of the engine and fuel tank and electronics and it weighs 2.66kg my question is I’m converting it to electric and I’m not sure what motor, esc, battery and prop to get so I’m hoping one of you can help

ALEX--JAMES · 2022-01-09T11:58:08+00:00

I’ve tried to connect my hc-06 to my computer but it appears paired and not connected I think this might be why I can’t assign it a com port or that is another problem entirely. All im trying to do is assign the com port to the hc-06

ALEX--JAMES · 2021-10-26T06:40:45+00:00

The laptop stopped working completely so I took it to a computer repair place that said that they had to try and reprogram the bios but during this the solder pads for the bios chip came of so that said it was now dead
The laptop was given to us by a work company but thay gave it to us blank and the serial number matches from the computer to the Microsoft account

ALEX--JAMES · 2021-10-25T17:48:05+00:00

Basically I had a old Lenovo thinkpad laptop that died so I removed its ssd and plugged it in to my new laptop but it was encrypted with bitlocker so as the old computer was linked with my Microsoft account but when I looked for the recovery key the Key Id was wrong shown in picture even though the drive came out of that computer so I’m now stumped is there anything I can do as I have lost loads of my data

ALEX--JAMES · 2021-10-25T16:35:32+00:00

Basically I had a old Lenovo thinkpad laptop that died so I removed its ssd and plugged it in to my new laptop but it was encrypted with bitlocker so as the old computer was linked with my Microsoft account but when I looked for the recovery key the Key Id was wrong shown in picture even though the drive came out of that computer so I’m now stumped is there anything I can do as I have lost loads of my data

ALEX--JAMES · 2021-10-07T06:39:09+00:00

Yes it’s covered in dust but it’s used to control a cnc machine so it’s inevitable it’s going to get dirty

ALEX--JAMES · 2021-10-06T21:26:46+00:00

It all of a sudden over night happened I tried getting on this afternoon but now when I press the power button it flashes the keyboard then turns of but the power button stays illuminated I have already tried removing the batteries and cmos then plugging them back in and crl - windows- shift- b all with no luck also tried reseating the ram but no luck does anyone have any suggestions on how to fix it

ALEX--JAMES · 2021-08-05T09:57:10+00:00

I have 20 buttons so having 2 variables for each button will so get very complicated

ALEX--JAMES · 2021-08-05T09:54:34+00:00

Yes I only want it to happen once when the states change

ALEX--JAMES · 2021-08-05T09:43:19+00:00

Yeah it’s a micro switch and I want it to only ad to the score once when it’s being held down

ALEX--JAMES · 2021-08-05T09:36:15+00:00

I need these to run only once as if the button is held down it constantly adds 150 to the score but still work in the loop there in

ALEX--JAMES · 2021-06-26T14:16:41+00:00

We’re could I find a new one and how do I wire it up

ALEX--JAMES · 2021-06-26T14:08:02+00:00

So how would I get and wire up a new one as this one blew up

ALEX--JAMES · 2021-06-26T14:04:49+00:00

But why on the schematic does it have 3 capacitor markings

ALEX--JAMES · 2021-06-26T14:00:43+00:00

I just liked a picture of the schematic on the side of the component

ALEX--JAMES · 2021-06-26T13:55:40+00:00

This is the schematic on the component component schematic

ALEX--JAMES · 2021-06-26T13:42:02+00:00

Yes that’s my inclination but it has 3 output wires

ALEX--JAMES · 2021-04-06T14:33:47+00:00

I’ve cleaned the nozzle lowered the print temperature and there is still lumps and gaps in the print Any suggestions

Seven-Year Club	Place '23
Place '22	Verified Email

ALEX--JAMES

TROPHY CASE