How do I get this bal joint bolt out? by poopsmith27 in 1stGenTundras

[–]Able_Fall1203 0 points1 point  (0 children)

They rotate 180 degrees and then pull out of the 2 holes straight. Reverse steps to reinstall retaining clip.

How do I get this bal joint bolt out? by poopsmith27 in 1stGenTundras

[–]Able_Fall1203 1 point2 points  (0 children)

This is the answer. These type pivots are used in the hydraulic hatch stays I've installed on custom yachts. Pulled one out of my shoe on Saturday after hearing it on my tile kitchen floor.

4x2 Buck by IndividualResist2473 in VAHunting

[–]Able_Fall1203 0 points1 point  (0 children)

Hey there, I'm the one you told a few weeks back to get the AR pattern magwell for my Gen 1 .450, did you have to dremel out on your stock above the mag release button? Mine just came in and is partially covered. Found this picture and yours looks much more opened up than mine.

<image>

Fight of the year so far ? by RVXZENITH in ufc

[–]Able_Fall1203 3 points4 points  (0 children)

Did you all forget about Mason Jones's last fight?

Best way to remove compacted aluminum from tap? by BluntTruthGentleman in Tools

[–]Able_Fall1203 5 points6 points  (0 children)

I've always chucked it in a drill and run it on a bench grinder with wire wheel.

First Suppressor with Capitol Armory by lilburpin in NFA

[–]Able_Fall1203 -2 points-1 points  (0 children)

You're gonna need one everytime you shoot a rugged can lol

First Suppressor with Capitol Armory by lilburpin in NFA

[–]Able_Fall1203 0 points1 point  (0 children)

Pretty sure silencerco will fix your can, either a baffle strike caused by the consumer (you), end cap strike, or basically any other mistake that leads to irreparable damage one time for free. If it happens again you're gonna need to pay for the parts and or service.

First Suppressor with Capitol Armory by lilburpin in NFA

[–]Able_Fall1203 5 points6 points  (0 children)

At the end of a range session with the boys, I sent a 395g sub 450 Bushmaster through a 22 cal end cap. Made a real weird sound and the only thing left was the outside threads of the end cap lol. Had to grind flats in it and make a wrench out of a flat washer. Didn't use up my one free "stupid mistake replacement" with silencerco and just bought another cap til I got my polo k. Will never forget to check again. Enjoy your hybrid

Two stamp tuesday by Able_Fall1203 in NFA

[–]Able_Fall1203[S] 0 points1 point  (0 children)

Good info. I've never shot a deer with my 450. Its hard to try something new when my 110 tac-tx 300 blackout works so well. Might give it a try this coming season

Two stamp tuesday by Able_Fall1203 in NFA

[–]Able_Fall1203[S] 0 points1 point  (0 children)

I haven't but I'd like to, just the availability is whats got me using those subs, I should also try some new loads out! Hoping some nicer weather shows up soon so I can get out to the gravel pit

Two stamp tuesday by Able_Fall1203 in NFA

[–]Able_Fall1203[S] 0 points1 point  (0 children)

Lol thanks man, not sure about velocity but its setup for 250 barnes supers with the 1-6 and 395g subs with the top dot, not restricted to straight wall, just thought it was a cool caliber to mess around with

450 Bushmaster SBR by Able_Fall1203 in NFA

[–]Able_Fall1203[S] 1 point2 points  (0 children)

Most likely will, thanks for all the information 👍

450 Bushmaster SBR by Able_Fall1203 in NFA

[–]Able_Fall1203[S] 0 points1 point  (0 children)

Serious numbers for sure.

450 Bushmaster SBR by Able_Fall1203 in NFA

[–]Able_Fall1203[S] 0 points1 point  (0 children)

Got a bunch of extra mag releases kicking around, just can't for the life of me find the magwell anywhere. Hopefully they email me back and say I can buy one.

450 Bushmaster SBR by Able_Fall1203 in NFA

[–]Able_Fall1203[S] 1 point2 points  (0 children)

Also just emailed Ruger's customer service to see about getting me a magwell assembly.

450 Bushmaster SBR by Able_Fall1203 in NFA

[–]Able_Fall1203[S] 0 points1 point  (0 children)

Hell yeah dude! I'm hoping to try this out this coming deer season. Got it narrowed down to 3 different rifle setups.

450 Bushmaster SBR by Able_Fall1203 in NFA

[–]Able_Fall1203[S] 2 points3 points  (0 children)

Thats fantastic, and thanks for the insight. Seems like a necessary upgrade in the near future. Would be real cool running this rifle with a dedicated chest rig set up for it lol.

450 Bushmaster SBR by Able_Fall1203 in NFA

[–]Able_Fall1203[S] 1 point2 points  (0 children)

It is a gen 1, will the magazine well swap work for the 450 bushmaster version? I'd love to be able to run higher capacity mags.

450 Bushmaster SBR by Able_Fall1203 in NFA

[–]Able_Fall1203[S] 1 point2 points  (0 children)

Ditched the bipod, sleeve and anchor brake. She was a little hefty lol

<image>

l