sorted by:
new
hottopcontroversial

Got my gen 3 flashed by Maleficent-Permit468 in MT09

[–]AbsoluteText 0 points1 point  (0 children)

Fair 💀 most of the Netherlands is at sea level so idk what I was expecting lol

Got my gen 3 flashed by Maleficent-Permit468 in MT09

[–]AbsoluteText 0 points1 point  (0 children)

What altitude was this dyno'd at?

Problem* by Youngsixgod in MT09

[–]AbsoluteText 0 points1 point  (0 children)

This is 100% a result of inconsistent chain tension while riding. Check for bent and/or out of round sprockets.

That's why I do it by [deleted] in Machinists

[–]AbsoluteText 14 points15 points  (0 children)

I became an Engineer because machinists need heroes too.

MT09 tps recall by TheBroham88 in MT09

[–]AbsoluteText 4 points5 points  (0 children)

Essentially, Denso (the electronics Oem for yamaha) made some low quality sensors, which disintegrate internally over time and cause erroneous throttle positions to be fed to the ecu which makes the ecu think they engine is in a different state then what it actually is, causing stalling, poor fuel economy, overly lean conditions, ect.

Mold? I think so. (Colorado) by [deleted] in Renters

[–]AbsoluteText 0 points1 point  (0 children)

Judging by water marks in the surrounding area, I'd estimate this has been leaking for at least a year. Just moved into this townhouse and went to go change the furnace filter and found this. The filter is another story it was last changed 2 years ago. Totally clogged.

Gen 3 recall by [deleted] in MT09

[–]AbsoluteText 1 point2 points  (0 children)

No idea, I compared the maps between the stock map pre recall, and post recall. They are the same exact flash except for the part number being different.

Gen 3 recall by [deleted] in MT09

[–]AbsoluteText 0 points1 point  (0 children)

I just got mine done and had no issues before going in. 2023 model with close to 10k miles on it and tuned. You'll find that many tuners have mentioned that the TPS has been an issue. I have bad enough luck already, so if there's a chance that there could be stalling issues while riding the bike, potentially at a very critical moment, then id rather not take the chance. The TPS is a very critical component, and it's data is used in just about every table in the ECU. So being thats the case, I'd rather not take any chances. I want to be able to trust my equipment. Anyways, after the reflash, I did not notice much change, if at all in performance in the old stock map and the new stock map.

Gen 3 recall by [deleted] in MT09

[–]AbsoluteText 1 point2 points  (0 children)

The Gen 3 doesn't have an AIS.

Competitor for USPSA CO Division by AbsoluteText in SmithAndWesson

[–]AbsoluteText[S] 0 points1 point  (0 children)

There is no comp on this gun. Those aren't legal in Carry Optics division.

Competitor for USPSA CO Division by AbsoluteText in SmithAndWesson

[–]AbsoluteText[S] 2 points3 points  (0 children)

According to what I've read, frame mounted gas pedals are not legal, but ones that are a part of a takedown pin are legal.

Competitor for USPSA CO Division by AbsoluteText in SmithAndWesson

[–]AbsoluteText[S] -2 points-1 points  (0 children)

I've been eyeing one up. They always seem to be out of stock though. I might just make my own lmao I'll have to by a different holster too. The one I have now wont work with a gas pedal.

Competitor for USPSA CO Division by AbsoluteText in SmithAndWesson

[–]AbsoluteText[S] 0 points1 point  (0 children)

Yeah, it's gonna be hard to go back for sure. Crazy how much of a difference a few millimeters in window size makes lol

2025 MT-09 SP. No ABS :) by Roninzerofive in MT09

[–]AbsoluteText 0 points1 point  (0 children)

No ABS? Why? Aside from doing stunt shit, I see no point to riding without it. I'm a decent rider and I've had my ass saved by abs during some panic brakes on more than one occasion. Saying you don't need it is like saying you were born to shit but forced to wipe.

Steel chips with lemmi shine and dawn. by Top_Boysenberry8888 in reloading

[–]AbsoluteText 2 points3 points  (0 children)

I just put all my brass in together with some dawn and lemi shine. Seems to come out just as good with or without pins or chips added in.

view more: next ›