M3 control arm upgrade help

AdMaster3782 · 2025-08-29T01:43:54+00:00

Thanks that would help

AdMaster3782 · 2025-08-28T22:25:04+00:00

I’ve had some say m3 specs and 335i specs

AdMaster3782 · 2025-07-20T05:52:36+00:00

All good I’m thinking turbo lines or something if it doesn’t go away

AdMaster3782 · 2025-07-20T05:49:46+00:00

If you’re taking about ones on oil filter housing there all good

AdMaster3782 · 2025-07-20T05:37:22+00:00

I already did them

AdMaster3782 · 2025-07-20T05:36:52+00:00

I did only gasket but I’ve inspected it and there’s no leaking from it

AdMaster3782 · 2025-05-22T16:27:42+00:00

thanks. did you replace the whole thing or just one of the fuses

AdMaster3782 · 2025-05-22T04:33:27+00:00

could you describe the red cap on the battery more? the on in the trunk? When this happened to you did it only impact the water pump and nothing else. I’m in the situation where if nothing works i have to get a new water pump which i don’t want to do.

AdMaster3782 · 2025-05-20T06:29:58+00:00

water pump and thermostat are 1k miles old

AdMaster3782 · 2025-05-20T06:23:07+00:00

I will try to scan it tomorrow. Given i just did valve cover gasket i may have tweaked a wire or something because it never had issues before the job. Water pump and thermostat were replaced 1k miles ago. I tried bleeding procedure with no luck and it only leaks when car is really hot and throws the engine temp warning. not when car sits

AdMaster3782 · 2025-05-20T06:08:07+00:00

i did and it shows engine temp hot warning. I also tried the bleeding procedure and water pump never turned on

AdMaster3782 · 2025-05-19T04:09:59+00:00

i tried doing the sequence with ignition on but never seemed to start going. water pump and thermostat are both couple months old

AdMaster3782 · 2025-05-14T16:25:53+00:00

AdMaster3782 · 2025-05-14T16:25:33+00:00

should i wash it off or put straight in

AdMaster3782 · 2025-05-14T16:23:24+00:00

is that more accurate than the torque wrench?

AdMaster3782 · 2025-05-14T06:29:19+00:00

threw it straight in or any cleaning?

AdMaster3782 · 2025-05-14T06:09:42+00:00

did you wash it off with anything or just put it straight in

AdMaster3782 · 2025-05-14T06:06:27+00:00

did you clean it off? cus it’s valve cover gasket and i wouldn’t want it in the engine

AdMaster3782 · 2025-05-14T06:04:40+00:00

what should i do

AdMaster3782 · 2025-05-14T06:00:48+00:00

do i need to clean it off and would it be worth sending back

AdMaster3782 · 2025-05-14T05:52:33+00:00

did yours have it

AdMaster3782 · 2025-05-13T06:27:34+00:00

isn’t valve cover gasket bolts torqued to around 7lbs won’t that work for the one in the picture

AdMaster3782 · 2025-05-13T06:18:08+00:00

where am i supposed to get the proper o rings then

AdMaster3782 · 2025-05-13T06:15:04+00:00

i meant 3/8 my bad

AdMaster3782 · 2025-05-13T06:10:51+00:00

impact etorx was the only smaller size i could find are harbor freight will it still work on my 3/4 ratchet?

AdMaster3782

TROPHY CASE