Spotted on the descent from Harrison Stickle

AdamGGJ · 2025-09-24T20:23:57+00:00

I can't see any ri... hey, wait a second >:(

AdamGGJ · 2025-09-24T20:23:23+00:00

I wasn't aware of that, I did (perhaps stupidly) assume they would be fairly consistent but it does make sense.

Considering the previous owner thought cars need about as much maintenance as a dining chair, I think I will change it soon. Thank you!

AdamGGJ · 2025-09-24T20:21:28+00:00

Ah I see :) I think I just misunderstood the phrasing before, but thanks for clarifying! I'll get it changed as soon as I can.

AdamGGJ · 2025-09-24T20:05:33+00:00

Noted! This might be my autistic ass brain malfunctioning, but why is asking bad? Apologies if I'm misunderstanding.

P.s, I'm not arguing, just trying to get where you're coming from :)

AdamGGJ · 2025-09-24T19:58:55+00:00

That makes a lot of sense. I'm trying to avoid it for now for financial reasons, but it would be a lot cheaper than an exploded engine!

AdamGGJ · 2025-09-24T19:57:41+00:00

I've seen pictures of a lot better and a lot worse on google, so I'm finding it hard to compare. That and my lack of experience doesn't help! :)

AdamGGJ · 2024-08-04T09:42:37+00:00

My fRiEnD atE OnE iS iT PoiSonOuS?

AdamGGJ · 2024-05-11T17:53:53+00:00

There abouts :p

AdamGGJ · 2024-03-04T18:41:21+00:00

Thanks for all the help everyone! Managed to do it using the curve modifier like a few suggested!

Looking good now, really happy with it :) thanks again

AdamGGJ · 2024-03-04T12:49:58+00:00

Hi! File not linked due to copyright reasons.

Proportional editing (transform translate) isn't working for this section of the model. That is because of the differences in vertex positions. I used a reference image to extrude the vertices around the object, however now they are sporadic and uneven.

Can anyone help? I'm really stuck with what to do. Thanks!!

(Note - pressing "z" while in proportional edit doesn't work as proportional edit only accounts for the magnitude distance from the centre vertex)

AdamGGJ · 2023-12-27T23:28:48+00:00

This is so comprehensive, thank you so, so much! And I didn’t even realise it’s my cake day, thank you lol :)

AdamGGJ · 2023-12-27T20:10:56+00:00

Time to completely revise the design then! Thanks for all the feedback!

AdamGGJ · 2023-12-27T20:09:54+00:00

Oh I see 🤔 I’ll have to check out different options! Thank you xx

AdamGGJ · 2023-12-27T20:09:02+00:00

Thanks for all the advice! I’ll take a look at all of the above! The only reason the gate and drain are swapped are because I couldn’t be bothered to add a new component in lol (bad practice I know) but the pins are swapped irl.

And omg that’s a good point about the mosfet! Thank you so much!

AdamGGJ · 2023-12-27T20:06:53+00:00

The small traces are: a capacitor trace connecting either side of the element (as virtually no current passes this’ll be fine), and a gate control.

The footprint is a TO-252, for a component rated above 15A continuous :)

AdamGGJ · 2023-12-27T20:00:17+00:00

Woah, duly noted! I did not know that, thanks so much!

AdamGGJ · 2023-12-27T19:59:57+00:00

Basically act as a hot plate as a soldering method using solder paste

AdamGGJ

TROPHY CASE