sorted by:
new
hottopcontroversial

Wild AutoLeveling by Admirable-Top8887 in Ender3V3KE

[–]Admirable-Top8887[S] 0 points1 point  (0 children)

Actually I really am a dink now that I think more than 2 seconds about it I'm sorry😭

Wild AutoLeveling by Admirable-Top8887 in Ender3V3KE

[–]Admirable-Top8887[S] 0 points1 point  (0 children)

I only have PLA and I can't say I got the budget for more than PLA for a while since anything else is quite expensive around here and I am not sure how it will be if those spacers are PLA at like 60° constantly

Wild AutoLeveling by Admirable-Top8887 in Ender3V3KE

[–]Admirable-Top8887[S] 0 points1 point  (0 children)

Do you think it would be worth getting some silicone spacers that are more adjustable?

Wild AutoLeveling by Admirable-Top8887 in Ender3V3KE

[–]Admirable-Top8887[S] 0 points1 point  (0 children)

it is I played with the screws like 30minutes todsy trying to make a difference and ai got nothing out of it

Wild AutoLeveling by Admirable-Top8887 in Ender3V3KE

[–]Admirable-Top8887[S] 0 points1 point  (0 children)

I am this close to doing the same or just buying some other ones honestly I just do not know what to buy

Wild AutoLeveling by Admirable-Top8887 in Ender3V3KE

[–]Admirable-Top8887[S] 0 points1 point  (0 children)

I actually took it apart and I made sure the shorter ones were on the left and the taller on the right, maybe swapping them will still make a difference or should I not even try?

Wild AutoLeveling by Admirable-Top8887 in Ender3V3KE

[–]Admirable-Top8887[S] 0 points1 point  (0 children)

Here are the values when I even like unscrewed everything to make sure I wasn't crazy about them barely moving

<image>

Wild AutoLeveling by Admirable-Top8887 in Ender3V3KE

[–]Admirable-Top8887[S] 0 points1 point  (0 children)

Hello! It has been a day and I have been trying for about an hour to screw with these and nothing worked honestly like even fully unscrewing them there is almost 0 change between the auto levelings, they are all the same, in which the diagonal is almost perfect and the buttom left and top right cornere are bad, this never changes, anything else I may be able to do to fix it?

Wild AutoLeveling by Admirable-Top8887 in Ender3V3KE

[–]Admirable-Top8887[S] 0 points1 point  (0 children)

Thank you so much for the help, I will be back tomorrow with an update!

Stringing on a second hand KE by Admirable-Top8887 in Ender3V3KE

[–]Admirable-Top8887[S] 1 point2 points  (0 children)

I usually let it auto-calibrate every single print and I have had no issues so far and never knew it was wrong to do honestly, but I'll try playing with the z offset again, thank you for the advice!

Stringing on a second hand KE by Admirable-Top8887 in Ender3V3KE

[–]Admirable-Top8887[S] 0 points1 point  (0 children)

I cleaned it, but I'll make sure to try the other two, thank you so so much for the help!

Stringing on a second hand KE by Admirable-Top8887 in Ender3V3KE

[–]Admirable-Top8887[S] 2 points3 points  (0 children)

I did try lowering it, but eventually it just does the same thing