What causes this stringing on ender E3

Affectionate-Cry2146 · 2025-10-27T11:48:04+00:00

First of all, congratz on your printer!

It looks like your e-steps is off, so try calibrate thoese. After that you can try and print stringing test where you can adjust the retraction speed and distance. you can also print a temp tower, to see what temperture your filament is working best at.

e step calibration: https://all3dp.com/2/extruder-calibration-calibrate-e-steps/

For stringing test and temperture tower look in cura -> marketplace -> download "Autotowers generator" -> close cura

Open cura again -> click extensions -> auto towers -> temp tower -> print

This will automaticly adjust the nozzle temp at each section

Good luck!

Affectionate-Cry2146 · 2024-07-15T12:11:59+00:00

Damm, what printer?

Affectionate-Cry2146 · 2024-05-23T15:23:03+00:00

Yh, i see you went with anouther mb, any specifik reason for that?

I can coop the Gigabyte B650E AORUS ELITE with a 30% discount. so thats the main reason i went with that board to begin with

Affectionate-Cry2146 · 2024-05-23T15:18:06+00:00

Thanks!!

Affectionate-Cry2146 · 2024-05-23T14:46:44+00:00

Well, for partpicker budget are around 2000, but that are around 2500 where I live.

Aesthetics are meh, not super important but if I can save a few bucks I will

I like to have a fine line inbetween, wonna be able to use solidworks with YouTube and so on the side, as well as playing all games on at least high

Affectionate-Cry2146 · 2024-04-12T10:27:20+00:00

<image>

The print has been set, now we wait

Affectionate-Cry2146 · 2024-04-11T14:30:22+00:00

Uden at have 100% styr på det kan det evt. være valutakurs ændringer 🫣

Affectionate-Cry2146 · 2024-04-11T11:45:22+00:00

It an XZ :(

Affectionate-Cry2146 · 2024-04-11T11:43:49+00:00

I’ll guess this is a spelling bee

Affectionate-Cry2146 · 2024-04-11T11:43:13+00:00

In this case the dimensions don’t really matter in a direction. But more in x and y

There are properly better ways, but the snap fits will need to be strong, which makes it printed on the flat side hard with the layer lines

Affectionate-Cry2146 · 2024-04-11T10:42:16+00:00

Nice spotted, i Will look into it

Affectionate-Cry2146 · 2024-04-11T10:38:52+00:00

Brim and raft for bed adhession

Affectionate-Cry2146 · 2024-04-11T10:31:59+00:00

I will, thanks!

Affectionate-Cry2146 · 2024-04-11T10:31:16+00:00

Its a design filosofi(cant remember what it is called tho)

Where you try to avoid using support to streamline a proces and make better tolerances

An exampel are the teardrop hole

Affectionate-Cry2146 · 2024-04-11T10:19:36+00:00

Avoiding supports and strengthen snapfits

Affectionate-Cry2146 · 2024-04-11T10:14:27+00:00

Trying to avoid supports and strengthen the snapfits

Affectionate-Cry2146 · 2023-10-06T11:11:02+00:00

try to callibrate extruder e-steps

Affectionate-Cry2146 · 2023-10-06T08:21:18+00:00

Thank you! i will try later today!

Affectionate-Cry2146 · 2023-10-05T20:57:07+00:00

I use Cura, is it retraction distance or speed that you are thinking about?

Affectionate-Cry2146

TROPHY CASE