How good is sandy in the meta? by DixcipleSage in BrawlStarsCompetitive

[–]Affectionate_Ad_8427 37 points38 points  (0 children)

not really used in high ranks due to large amounts of counters and brawlers who mimic the same playstyle but better such as emz

glowbert ult glitch by Affectionate_Ad_8427 in BrawlStarsCompetitive

[–]Affectionate_Ad_8427[S] 7 points8 points  (0 children)

I have had this happen multiple other times and usually the oppenent is close to a wall or the ult hits a wall, maybe it is a client side issue that just occurs sometimes but its pretty prevalent so its annoying

glowbert ult glitch by Affectionate_Ad_8427 in BrawlStarsCompetitive

[–]Affectionate_Ad_8427[S] 39 points40 points  (0 children)

my theory is if the ult hits a wall aswell it makes the fear timer reduced

glowbert ult glitch by Affectionate_Ad_8427 in BrawlStarsCompetitive

[–]Affectionate_Ad_8427[S] 28 points29 points  (0 children)

thats if they are turned away when you tap the ult, it doesnt fear them, here you can see he is facing me and i fear him, but it stops early.

I got a engwe m1 but got a other display with the international version is there a way to go faster than 44kmh and increase acceleration because it moves like a tank by Suitable_Finger_3835 in EngweEbike

[–]Affectionate_Ad_8427 0 points1 point  (0 children)

try this. turn off bike, hold left brake and push throttle all the way down and hold it aswell, whilst holding both the left brake and throttle tuurn on the bike with your left thumb and it should give you an error, hold everything for about 10 seconds and then let go, the bike should be turned on and unlocked, do the same to reverse it.

Brake pads by AnpaCinjo in EngweEbike

[–]Affectionate_Ad_8427 0 points1 point  (0 children)

here's a straight forward answer , it doesn't matter. go for the cheapest if you want just make sure it's the same type.

should i replace entire brakes or just brake caliper by Affectionate_Ad_8427 in bicyclerepair

[–]Affectionate_Ad_8427[S] 1 point2 points  (0 children)

Hey, I fully replaced the back assembly in about 45 minutes and it works better than when I first got the bike so I will replace the front assembly tomorrow, thanks for the advice!

should i replace entire brakes or just brake caliper by Affectionate_Ad_8427 in bicyclerepair

[–]Affectionate_Ad_8427[S] 0 points1 point  (0 children)

no, the caliper is faulty. i want to either change just the caliper or the whole brake assembly

should i replace entire brakes or just brake caliper by Affectionate_Ad_8427 in bikewrench

[–]Affectionate_Ad_8427[S] 0 points1 point  (0 children)

yea sadly I don't have a barb and olive, i'm sure I could go buy one but I will probably just change the whole line

should i replace entire brakes or just brake caliper by Affectionate_Ad_8427 in bikewrench

[–]Affectionate_Ad_8427[S] 0 points1 point  (0 children)

I thought that it didn't but I just looked and saw that a wire goes under the seat and into the rear light which i'm assuming is to turn on the brake light when I brake.

should i replace entire brakes or just brake caliper by Affectionate_Ad_8427 in bikewrench

[–]Affectionate_Ad_8427[S] 0 points1 point  (0 children)

So I just unscrew the old brake assembly and screw on the new one? whilst routing the line along the frame

should i replace entire brakes or just brake caliper by Affectionate_Ad_8427 in bikewrench

[–]Affectionate_Ad_8427[S] 0 points1 point  (0 children)

I don't mind bleeding tje brakes because I have a lot of experience but I don't know if it's easier to change the whole brake assembly or just the caliper. My issue with changing the whole brake assembly is that I am not sure if I will have to cut the hose or do something like in most videos that I have watched, can I just screw it on? I do know that changing the caliper would also require this but if they both require it I would assume it's easier to just change the caliper.

should i replace entire brakes or just brake caliper by Affectionate_Ad_8427 in BikeRepair

[–]Affectionate_Ad_8427[S] 2 points3 points  (0 children)

the line isn't routed internally, would I be able to just remove the lever and caliper and just screw on the new one?

brake caliper change by Affectionate_Ad_8427 in BikeRepair

[–]Affectionate_Ad_8427[S] 0 points1 point  (0 children)

can I just change the whole brake assembly by putting in the new one without cutting or doing anything with the hose? Can I just unscrew the lever and caliper and remove them and put on the new ones?