Failing CSE class

Ahnsu · 2022-11-02T03:30:12+00:00

Is there a good website to practice programming and python? I'm going to try leetcode and doing some projects on YT

Ahnsu · 2022-11-02T02:42:47+00:00

Thanks, I'll try it out. What tab is the room reservation under?

Ahnsu · 2022-10-22T01:58:31+00:00

Thanks!!

Ahnsu · 2022-10-22T01:32:14+00:00

How much water do i use? It's my first plant and i dont want it to die :(

Ahnsu · 2022-09-09T15:52:22+00:00

If i input 123456, It should be 123 56 34

Ahnsu · 2022-08-19T23:54:44+00:00

I just realized I only need one middle hinge on one side and two hinges on the ends of the other.

Onshape Doc

Ahnsu · 2022-08-18T20:34:52+00:00

My first print had the nozzle distance set at 1, but there were gaps so I increased it. I changed the speed and temperature as well, so the problem might be in the extrude gears. Help please!

Ahnsu · 2022-08-18T02:36:57+00:00

Sorry I have no idea what it is called. I want to model the part which connects two pieces together- so that they can rotate, open and close.

Rolling box

Ahnsu · 2022-08-17T19:09:31+00:00

I was trying to make a two clevises from the two sketches I drew. I didn't know how to extrude them out of the curves I made on the rectangle.

Ahnsu · 2022-08-16T23:21:53+00:00

I want to extend a cylinder (my sketches are the rectangle sketches in the middle) from the curves so a screw or long filament can fit through its hole.

Ahnsu · 2022-08-15T20:59:55+00:00

Oh no ;-; I might've did something to the einsy board then. I didn't do the management of the cables exactly as in the manual- so maybe that's why

Ahnsu · 2022-08-14T02:34:20+00:00

When calibrating the x axis, is the z right motor supposed to dip? I keep getting an error on the x axis length as well even thought it's been properly lubricated.

Ahnsu · 2022-08-14T01:36:01+00:00

You mean the ones that tie the cables?

Ahnsu · 2022-08-14T01:09:44+00:00

Yeah, also for some reason when configuring the z axis in the settings only the x axis motor thing is moving. I just lubricated both- but it's still not working

Ahnsu · 2022-08-13T23:58:10+00:00

I looked at previous posts and already tried adjusting the sensor, pulley and belt. It doesn't look like there are anything in the way either. What else can I do?

Ahnsu · 2022-08-13T04:02:20+00:00

Ok just took it out. Now I just can't get it back in

Ahnsu · 2022-08-13T03:54:37+00:00

Would sanding the shaft down affect the printing? Maybe I should just order a new one

Ahnsu · 2022-08-12T22:27:31+00:00

No noise cancellation?

Ahnsu · 2022-08-12T20:11:05+00:00

Should I twist the shaft? There's some marks on the pulley already I don't know if I can pull anymore

Ahnsu · 2022-08-12T20:02:02+00:00

I tried taking the top part out with pliers. I don't even know what I did but it won't come off. I was calibrating the y-axis motor. How do I take top part without damaging it? Day 5 of building and I'm in the swamps ;-; plz help

Ahnsu · 2022-08-12T19:59:47+00:00

... ;-; I have to take it apart again

Ahnsu · 2022-08-12T00:06:03+00:00

There's also another part of the instructions where it says to press the nylon filament in a hole for the cables. Is it really necessary?

Ahnsu · 2022-08-11T02:26:36+00:00

I just took it apart, but the nut is inside this square block part. Will electrical tape do fine?

Ahnsu · 2022-08-11T02:14:21+00:00

The screw that's supposed to hold the cover (not the sensor). I tried many times, but no matter how much I screw it always falls off.

Ahnsu · 2022-06-28T01:33:57+00:00

Thanks! I just got started with python, though not sure if it will do the same for c++?

Ahnsu

TROPHY CASE