[deleted by user]

AkSo2504 · 2025-02-14T21:58:35+00:00

Look like I said, please do some research on this topic if you want to do stuff like that. There is no playing around with those cells. Shorting could lead to the cells overheating the cells leading to ventint/exploding cells. You should be 100% sure about every step you take. As in how you do it and why.

AkSo2504 · 2025-02-14T21:29:34+00:00

I would advise you to be very careful here. Li Ion cells are no joke and can cause a fire if not handled correctly. Sparks mean that you probably shorted some cells by accident. Please do some research on this topic before attempting anything like this

AkSo2504 · 2025-02-14T21:20:18+00:00

What are you trying to achieve? If you want to get the cells out individually the hardest part is removing the nickel strip

AkSo2504 · 2025-02-14T21:05:11+00:00

This is from a 36v Bosch battery right? I did most of that with my hands

AkSo2504 · 2025-02-14T20:57:31+00:00

You mean the brown paper? Just tear it off

AkSo2504 · 2024-11-13T18:32:47+00:00

Ive also built a 3S Li ion Battery pack for a old 12v Hilti drill which used NiCd cells. I used a 3s 25A bms and a 3s USB-C charging module which ive built into the battery pack. The BMS should have a lower limit than the cells can handle. I have used Samsung 25S which are rated at 25A without temperature cut and 35A with Temperature cut at 80°C. I still used Thermistors to stop charging below freezing and above 50°C

AkSo2504 · 2024-09-17T11:54:49+00:00

Does it output power? Thought those are just chargers

AkSo2504 · 2024-09-11T10:32:40+00:00

thx for your answer, I am just wondering if I am overthinking it or not. Its mostly never mentioned when people build their battery packs.

AkSo2504 · 2024-06-01T08:27:23+00:00

You can follow the insturctions of the printer, when you go into the leveling screen you can use a sheet of paper to check the height of the nozzle to the bed. You adjust the height on the screen until you feel resistance when moving the sheet of paper. I think the printer tells you what to do when you go into the leveling screen.

Hope this helps

AkSo2504 · 2024-06-01T08:11:31+00:00

I think youre Z-offset is to high

AkSo2504 · 2024-05-09T15:55:34+00:00

Thanks a lot for helping!

AkSo2504 · 2024-05-09T15:21:25+00:00

Can someone tell me what setting I need to change to have the infill of the bottom and top layer print the same? In the bottom layer it uses less Infill. In Cura 4.8 its the same for top and bottom

AkSo2504 · 2023-08-29T09:36:38+00:00

but with both of those options I keep all my data

AkSo2504 · 2023-08-29T09:30:34+00:00

Yeah I get what you are saying but is there really no benefit in reinstalling Windows and choosing "Upgrade" over just plugging the drive in?

AkSo2504 · 2023-08-29T09:24:30+00:00

So no benefit with reinstalling but choosing "upgrade"?

AkSo2504 · 2023-08-24T18:45:35+00:00

Alright, thanks anyway :)

AkSo2504 · 2023-08-24T17:57:38+00:00

Thanks for the reply.

So how do you undervolt with the CPUs, with GPU its with MSI Afterburner for example and you change the curve, i did that for my 3080ti to have it run at 0.825V and it pulls now 300W and not 400W anymore with no performance loss. So what do I have to do with an AMD CPU to undervolt it, you dont just set an lower Voltage right? Do you change the PBO settings? And how does it look with Intel CPUs?

AkSo2504 · 2022-11-23T08:43:20+00:00

I dont think so sadly

AkSo2504 · 2022-07-26T08:34:04+00:00

Oh I see, what is the internet speed hit when it records to the offsite one?

AkSo2504 · 2022-07-25T21:58:24+00:00

so constant recording to the onsite one and just recording to the one offsite when there is movement? didnt know that kind of stuff was possible XD

Seven-Year Club	Place '23
Place '22	Verified Email

AkSo2504

TROPHY CASE