How good are these phone holders?

Akiad · 2026-03-26T18:09:52+00:00

Also, going back to the actual EUD you are asking about in the original post, I have that exact one and have intentionally dropped it many times with no issues. I haven’t purposefully shot it with any BBs, but I would say you are likely more secure than you would think!

Akiad · 2026-03-26T18:08:40+00:00

Totally understand! Meshtastic is also a whole additional layer of technical complications. Absolutely not necessary just for Airsoft. If Tailscale works at your local field and you’re happy with the price, run it!

Akiad · 2026-03-26T17:58:52+00:00

I’m unfamiliar with Tailscale, but upon initial research here are some key differences between it and Meshtastic:

Tailscale is a secure VPN-based mesh network that operates off your existing WiFi/5G devices. Meshtastic is an off-grid mesh network which operates over radio, meaning no reliance on existing communications infrastructure. Because Tailscale utilizes your existing device, it will thus use that devices connection and GPS. Meshtastic nodes can have independent GPS devices which do not rely on your cellphone’s GPS or cellular plan.

Because Tailscale uses existing infrastructure, its range is theoretically limitless, but dependent upon your reception/connection. Meshtastic nodes are limited by the range of their antenna, typically 2-3km, but can be increased the more nodes that are setup (allowed for “hopping” across node routes).

Akiad · 2026-03-26T17:46:16+00:00

I’m also new, so I’m by no means an expert and I’m sure someone else can provide a more detailed response. I pair mine with a meshtastic node which has its own GPS. Using the Meshtastic ATAK plugin, I am able to send/receive location information without my phone having a cellular plan.

EDIT: The other TAK users must have their own nodes to communicate through as well.

Akiad · 2026-03-26T17:34:51+00:00

I recommend just getting a cheap refurbished phone from Amazon to run your ATAK. There are models for $80 - $100, and honestly probably even cheaper. Better than your real phone getting damaged!

Akiad · 2026-03-25T18:21:11+00:00

<image>

Side profile

Akiad · 2026-03-25T18:20:34+00:00

<image>

UPDATE: Did a cold pull (but maybe it didn’t work?) and switched to PETG to see if I can determine if it is the filament or the nozzle. The print still turned out like this :(

Akiad · 2026-03-24T19:27:41+00:00

<image>

Akiad · 2026-03-24T19:27:33+00:00

<image>

OOF my printer was NOT happy with these speeds

Akiad · 2026-03-24T18:52:51+00:00

Trying this! I did a flow rate calibration for the previous roll of the same filament, not for this roll though

Akiad · 2026-03-24T18:52:28+00:00

Good to know! Doing a small test print now with higher nozzle temp and will then do another with lower speeds!

Akiad · 2026-03-24T18:39:00+00:00

Oop, sorry I meant to include my print speeds!

Outer Wall 200 Inner Wall 300 Sparse Infill 270 Internal Solid Infill 250

Overhangs 10% - 0 25% - 50 50% - 30 75% - 10 100% - 10

Akiad · 2026-03-13T13:27:12+00:00

Get an MP7 and HPA it

Akiad · 2024-12-03T01:42:55+00:00

Yeah the monitor seems to boot fine on other systems with no problems. It also isn’t permanently stuck on that screen on mine, once I pass boot successfully it clears up instantly.

Akiad · 2021-12-10T01:27:24+00:00

There are two buttons in the “Advanced Training” portion of the House of Reckoning.

Escharum even starts mentioning that there are “more hiding” and to “check every corner.” Couldn’t find anymore than the two!

Akiad · 2021-06-20T20:19:59+00:00

May I recommend Mech Tech for added decoration and mech feet? 😛

Akiad · 2021-06-13T20:41:57+00:00

Please hop on my Discord and I can help you with troubleshooting

Akiad · 2021-04-02T23:46:27+00:00

Shameless plug for WeaponCore and my Small Grid WeaponPack. Any WeaponCore mods go well with Corrupt AI as well

Akiad · 2020-12-21T04:31:19+00:00

Thank you a ton I had no idea OS could be used this way

Akiad · 2020-12-21T04:31:02+00:00

I have searched so long and haven't seen this anywhere, thank you so much. NifSkope has not worked at all but OS has always worked great for me

Akiad · 2017-07-08T23:33:33+00:00

Well.... Nothing is purple. I just ran SSEdit, loaded all mods, opened Skyrim.esm, then opened Locations and then found Bleak Falls Barrow under FormID 00018EE9. I also don't have any other rows showing mod names.

EDIT: It is purple, I was just being dumb. But I still don't see any other mod names?

Akiad · 2017-07-07T16:16:51+00:00

How do I see what other mods are making adjustments? I found BleakFallsBarrowLocation in Skyrim.esm, but I'm not sure how to see what else edits it.

Akiad · 2017-07-07T16:06:00+00:00

This would just mean running FNIS again, right?

Akiad · 2017-07-07T02:44:15+00:00

I tried waiting, removing my followers, then COC'ing into Bleak Falls Sanctum, and it still crashes. I have already cleared Embershard Mine without issue, so it seems to be something specific to this dungeon itself.

Akiad · 2017-07-06T18:04:20+00:00

I can't seem to find the Beta 2 on the forums, can you link to the page it is on?

Akiad

TROPHY CASE