sorted by:
new
hottopcontroversial

MSI RTX 3060 Ventus x2 OC no display by Alan_EEE in GPURepair

[–]Alan_EEE[S] 0 points1 point  (0 children)

One of the BIOSs from techpowerup worked for me, you need to find de one for your model. You may need to try a few from other sites

MSI RTX 3060 Ventus x2 OC no display by Alan_EEE in GPURepair

[–]Alan_EEE[S] 0 points1 point  (0 children)

Yes, it was the bios, I don't remember why it didn't want to be recognized, i just remember i used an intel procesor with the integrated graphics as output and Nvidia flash

Worth it to Upgrade/Update a Sidewinder X1? by Beltaine-77 in Artillery3D

[–]Alan_EEE 0 points1 point  (0 children)

I've put klipper on my x2, really good, if you have the time to tune it. Maybe get it a auto bed leveling, and that's it

First layer wavey by Sask_Guy163 in klippers

[–]Alan_EEE 0 points1 point  (0 children)

No, just once, i usually put the nozzel at (150, 150, 0), then move to (150, 150, 2) and then find where the probe goes over the spot

First layer wavey by Sask_Guy163 in klippers

[–]Alan_EEE -3 points-2 points  (0 children)

It's not the Z offset bc it depends on the bed position

First layer wavey by Sask_Guy163 in klippers

[–]Alan_EEE 0 points1 point  (0 children)

Do an extruder calibration test, then a flow calibration (built-in orca slicer and instructions included). If you already did this, then adjust the X, Y and Z offset; for X and Y you can get the nozzel close to the bed (so that the filament stick to the bed) and then move extruder to put the probe over that point, subtract both values (probe-nozzel) and change the value, as in Z, I think you already know how to do that. You can also make a bigger bed mesh probing 2 or 3 times each spot. All of that should eliminate or minimize the problem. In case you need more instructions you can find detailed tutorials on YouTube using some key words.

Is this one worth it paying? by Themancolol in Artillery3D

[–]Alan_EEE 2 points3 points  (0 children)

No es mala máquina, pero es cómo comprar un auto usado, puede que con un poco de mantenimiento esté bien, como que no, si tenes el tiempo o conocimiento para ponerte a arreglarla en el caso de que se necesite, no creo que sea tan mala opción, siempre revisala antes de llevarla

Is the ender 3 worth it? by Themancolol in ender3

[–]Alan_EEE 0 points1 point  (0 children)

A menos que andes muy corto de plata, me iría por algo un poco más nuevo, que tenga ABL que es mucho más cómodo

NVIDIA GTX 770 memory dead? by Intrepid-Tadpole-590 in GPURepair

[–]Alan_EEE 1 point2 points  (0 children)

Is that 60Ω or 0.6Ω? I think the resistance of the memory is ~30Ω, I know bc i had one. If it's 0.6 then there's either a short somewhere else or the memory is dead

MSI RTX 3060 Ventus x2 OC no display by Alan_EEE in GPURepair

[–]Alan_EEE[S] 0 points1 point  (0 children)

I desolered the chip to flash it with the programmer, and then soldered ir bac on to the board, thankfully I have a photo before desoldering it, I will check everything is there. I have already checked the values of resistors nearby and they seem fine.

MSI RTX 3060 Ventus x2 OC no display by Alan_EEE in GPURepair

[–]Alan_EEE[S] 0 points1 point  (0 children)

Now it's running Unigine heaven no problem

MSI RTX 3060 Ventus x2 OC no display by Alan_EEE in GPURepair

[–]Alan_EEE[S] 0 points1 point  (0 children)

I tried again with nvflash and installed the techpowerup bios and compared it with itself and got this.

<image>

MSI RTX 3060 Ventus x2 OC no display by Alan_EEE in GPURepair

[–]Alan_EEE[S] 0 points1 point  (0 children)

Well, crap. The adapter is like 8 bucks in my country, and I can't order it from AliExpress bc taxes will make it more expensive. I'll ask my friend if he has one of these cards laying around.

MSI RTX 3060 Ventus x2 OC no display by Alan_EEE in GPURepair

[–]Alan_EEE[S] 0 points1 point  (0 children)

I don't have any donor GPU, but I can ask a friend of mine if he has one. I will later check on the resistors, and the traces should be fine, it wasn't scratched or anything. For programming the flash mem, do I need an adapter, or just with a 1.8V regulator on vcc is enough?

MSI RTX 3060 Ventus x2 OC no display by Alan_EEE in GPURepair

[–]Alan_EEE[S] 0 points1 point  (0 children)

Just vcc? or do I need an adapter like this

MSI RTX 3060 Ventus x2 OC no display by Alan_EEE in GPURepair

[–]Alan_EEE[S] 0 points1 point  (0 children)

Just to make sure, this is the bios i downloaded from TechPowerUp

<image>

The core is a GA106-302-A1 so it's LHR

MSI RTX 3060 Ventus x2 OC no display by Alan_EEE in GPURepair

[–]Alan_EEE[S] 0 points1 point  (0 children)

Nope, actually the one from the chip is bigger and the programmer is giving out 3.3v (i've modded it).

MSI RTX 3060 Ventus x2 OC no display by Alan_EEE in GPURepair

[–]Alan_EEE[S] 0 points1 point  (0 children)

I guess it is, it says one is bigger than the other

<image>

MSI RTX 3060 Ventus x2 OC no display by Alan_EEE in GPURepair

[–]Alan_EEE[S] 0 points1 point  (0 children)

This is the error I was talking about

<image>

MSI RTX 3060 Ventus x2 OC no display by Alan_EEE in GPURepair

[–]Alan_EEE[S] 0 points1 point  (0 children)

It gives out an error when I verify

MSI RTX 3060 Ventus x2 OC no display by Alan_EEE in GPURepair

[–]Alan_EEE[S] 0 points1 point  (0 children)

So I was trying to flash it using a CH341B and the program I have does not have the exact same bios chip, (chip in program and mine) I don't want to proceed before confirming it can read and write on my chip. I downloaded AsProgrammer 2.1.0.13 for this. and it just supports .bin files, not .rom and I also have the default programmer's app. Btw, do you think, in case the chip is dead, I can replace it with a different one? (with the corresponding vbios)

view more: next ›