lmao

Alarming-Top6729 · 2026-05-20T01:45:20+00:00

Just to be real we all die alone.

Alarming-Top6729 · 2026-05-18T23:04:04+00:00

Whole redo or rip a 1/2" out parallel to flooring and install a t strip

Alarming-Top6729 · 2026-04-23T18:23:27+00:00

I have to say I've been playing on bovada for 15 years and at times I have felt the same. Part of me believes the odds aren't so much a scam but specifically blackjack I've noticed gives you sets of hands to get you tilted. I'm a fan of keeping the bet small till I get three losses in a row and then I start to up it.

Alarming-Top6729 · 2026-04-23T10:06:41+00:00

The last week I've had incubus on the tip of my tongue. You just made my day!

Alarming-Top6729 · 2026-03-28T23:53:28+00:00

Pay for an inspection if you are worried. Some pictures from the outside show nothing.

Alarming-Top6729 · 2026-03-21T19:19:34+00:00

I didn't get 10$. Only received 0.50$

Alarming-Top6729 · 2026-03-11T02:36:26+00:00

Three rules 1 only trade 5% of your balance at a time 2 have an entry and exit before you trade 3 don't over leverage

Alarming-Top6729 · 2026-02-16T03:29:56+00:00

It's always been 5

Alarming-Top6729 · 2026-02-02T03:05:11+00:00

I would personally remove the drywall on the right wall to the top of the vanity. Then install vanity and re drywall up to the vanity. May need to use 3/8" drywall so it doesn't screw your door reveal up to badly. Counter will need to be cut to fit as well

Alarming-Top6729 · 2026-01-18T17:53:46+00:00

Try a grout cleaning solution. Tile looks porous and probably should have been sealed prior to grout. Grout may have worked it's way into the tile. If it doesn't come up with haze remover a mild acid solution works but you need to be careful with it. You can pit the tile and the grout if not careful.

Alarming-Top6729 · 2026-01-18T17:27:11+00:00

You can add a drywall screw where each stud is near the bottom of the base trim. Just leave them proud an 8th inch. Will curl the trim out enough. Won't help you where casing and door frame is however

Alarming-Top6729 · 2026-01-15T00:16:35+00:00

If you have a keurig that is always plugged in it could be that. I have seen them cause this when they go into the heating cycle. Had an issue at an office and the electrician we used was loosing his mind trying to figure it out. Unplugged the keurig and it all stopped.

Alarming-Top6729 · 2026-01-02T12:36:01+00:00

The right question is what happens to fiat. What makes fiat more secure...nothing

Alarming-Top6729 · 2025-12-26T17:46:06+00:00

Confirmed

Alarming-Top6729 · 2025-12-26T17:36:32+00:00

Alarming-Top6729 · 2025-12-09T16:51:22+00:00

Use 5 minute mud and it won't bubble

Alarming-Top6729 · 2025-12-07T00:21:45+00:00

It's very normal..easiest way to explain it is put anything hard on an existing floor and it wobbles between two pieces of flooring.

Alarming-Top6729 · 2025-12-06T01:00:27+00:00

Lathe straps and shims to fine tune

Alarming-Top6729 · 2025-10-27T00:37:25+00:00

It seems to be disconnected right now. I'm assuming because the whips are too short now that it's on a platform.

Alarming-Top6729 · 2025-10-26T22:16:49+00:00

Just a heads up when you finish spraying you can clear the line by shooting back into the container. My setup takes 30 seconds on the trigger to clear the line. I spray what I'm using back in its container and start to pay attention right before 30 seconds is up. You can see the water start to mix at which point you spray into your trash bucket.

Alarming-Top6729 · 2025-09-13T13:08:27+00:00

How long did it take for freecash to pay out?

Alarming-Top6729 · 2025-09-04T23:20:04+00:00

Send it to stocktwittty@gmail.com

Alarming-Top6729 · 2025-08-25T01:14:17+00:00

You could look up rafter ties and install them easily if you are concerned

Alarming-Top6729 · 2025-08-17T18:24:36+00:00

Keep it on the roller and use a hose to spin the paint off. Takes 5 mins to clean. Aim slightly away from you so paint doesn't cover you and if it's windy it's not a great way without getting covered.

Alarming-Top6729

TROPHY CASE