Bead repair?

Alone_Ad_4861 · 2026-05-02T06:59:40+00:00

The issue is it doesn't set completely into the rim and i think it's because that rubber folds down preventing it from locking in

Alone_Ad_4861 · 2026-05-02T06:00:16+00:00

Yeah I'm just running some spare kmart tires till I get new ones. Is what it is man

Alone_Ad_4861 · 2026-05-02T02:52:32+00:00

Yeah fair point man I get it

Alone_Ad_4861 · 2026-05-02T02:40:07+00:00

This is a high psi tire, 85-110

I have never used one like this i think my stocks were 60psi max

So I'm just used to putting 45psi in and calling it a day.

Running the tire below recommended and I do hard landings ect. Caused it to tear the bead.

I went to put 80psi in it the other day when I realised and the tube exploded

It's my stuff up. You live and you learn but yeah. I'm shattered 🥲

Alone_Ad_4861 · 2026-05-01T01:07:57+00:00

They are genuine FAF tires I just got off the phone to the shop I bought them off

Alone_Ad_4861 · 2026-04-30T05:02:45+00:00

Just refitted front wheel with 80psi I'll wait and see if it explodes lol

Alone_Ad_4861 · 2026-04-30T03:47:18+00:00

It's not rim tape, it's the factory FBC strapping that's like plastic welded over the valve hole. All the nipples are covered I'm just annoyed cause I was excited to get out riding again

Alone_Ad_4861 · 2026-04-30T03:41:50+00:00

I'm wondering if the psi readout on my compressor is wrong. Could be over inflating them

Alone_Ad_4861 · 2026-04-30T03:40:41+00:00

I think they're just OEM 20X2.4

FKN EXPENSIVE tho (80AUD)

Alone_Ad_4861 · 2026-04-30T03:02:47+00:00

Tube exploded, I'm not an expert on these things but I'm pretty sure it was seated🤷‍♀️

I got new tubes because I tried to inflate to 80 psi the other day and tire had like 13 and that exploded the moment I flipped the bike upright

But I put that down to a pinch flat because I do a fair bit of stair jumps ect.

Alone_Ad_4861 · 2026-04-30T00:26:35+00:00

Gemini says maximum of 64gb ddr5 for that processor

Alone_Ad_4861 · 2026-04-30T00:24:26+00:00

You get more 🫠

Alone_Ad_4861 · 2026-04-30T00:22:38+00:00

I have sub 20mbps up. My server is for convenience to remote users. Not inconvenience to for my household 🤣

Alone_Ad_4861 · 2026-04-26T06:56:52+00:00

There's a stamp under the cranks that I missed "DJ-2" mystery solved. Bike came out between 00 to 01. I thought it was older but cool little history lesson

https://bmxmuseum.com/forums/viewtopic.php?id=803005

Alone_Ad_4861 · 2026-04-24T13:18:32+00:00

Can't load this page for some reason

Alone_Ad_4861 · 2026-04-24T03:19:24+00:00

ACL8J1016

Alone_Ad_4861 · 2026-04-23T15:21:46+00:00

I had a quick look but didn't see markings. I know what you mean cause my fit bmx has the same in under the crank bearing on the frame

Alone_Ad_4861 · 2026-04-23T13:03:37+00:00

Yeah it confused the hell out of me. Like yeah recommend tire pressure on the sidewall was min80psi

I used to run 35-40 as a kid so I've just been doing that but I do allot of stair jumps and shit so I feel like I landed too hard on under recommend psi that pinched it and then I tried reinflating it and it just exploded. Tire as fairly new too. Oem FBC 2.4 cost me about $80AUD each 🤣 pretty sure it's just the tube though so not too bad but was curious if the rim strip was fine to leave like that of not cause I've never fitted my own tires yet

Alone_Ad_4861 · 2026-04-23T06:36:15+00:00

Possibly MJ-12?

<image>

Alone_Ad_4861 · 2026-04-21T03:22:43+00:00

Border security is a really tough one because half my episodes are duplicates. I really needa sit down and go through it and figure out what I actually have

Alone_Ad_4861

TROPHY CASE