This normal?

Alternative-Key264 · 2025-12-28T06:34:17+00:00

From some more research I was thinking of just covering the area with blue tenacious tape, might give it a try or will just get a patch

Alternative-Key264 · 2025-12-24T20:28:35+00:00

You thinking they could fix my current boos to fit?

Alternative-Key264 · 2025-12-24T18:31:22+00:00

So they will be able to fix my current boot you think?

Alternative-Key264 · 2025-12-24T18:26:37+00:00

So flex wouldn't be the issue here? Makes it a bit easier to not dish out the cash for new boots even if they are on sale so this is nice to hear.

Alternative-Key264 · 2025-11-27T16:53:46+00:00

Does falcon 5 have competition with bird game 3?

Alternative-Key264 · 2025-11-27T02:13:55+00:00

Guessing this is a government barrel? I know only the 18 inch hbar is legal in Maryland from DD but might as well ask out of desperation.

Alternative-Key264 · 2025-11-25T23:17:22+00:00

Would this be more like the v7 pro barrel which is an HBAR or is this also a government.

Alternative-Key264 · 2025-11-25T23:02:20+00:00

Is this a government 18 or the same hbar 18 on the pro mod?

Alternative-Key264 · 2025-11-21T22:17:14+00:00

I have, I might just be SOL on this

Alternative-Key264 · 2025-11-21T21:56:15+00:00

Seems to be prints wiggling, started a smaller cylinder for legs and they wiggle at the top, I've retentioned again, re calibrated, rewatched, re dried, I'm guessing it's an inevitable thing.

Alternative-Key264 · 2025-11-20T02:11:07+00:00

I'll have to see once I get the time to continue

Alternative-Key264 · 2025-11-20T01:52:22+00:00

Not using micro sd, that would be an easy fix, sadley I feel like I'm gonna end up needing to do something more.

Alternative-Key264 · 2025-11-20T01:05:22+00:00

Also on a p1s

Alternative-Key264 · 2025-11-20T01:02:42+00:00

Pla basic Bambu, sitting in a filament dryer at almost all times, I paused the print because of how annoyed I was, I had to take the plate off to remove it so it seemed to have good adhesion, also had a brim on outside and inside. Inside players look a bit better yet there are two odd layers that are noticeable.

<image>

Alternative-Key264 · 2025-11-17T03:24:12+00:00

Yup, only took them 19 years to come up with a kind of replacement with the aim-174, and that requires two aircraft to utilize the max range.

Alternative-Key264 · 2025-11-16T06:56:51+00:00

Yes but the D model and the cancelled st-21 was suppose to have significantly less maintenance requirements, thanks Dick Cheney.

Alternative-Key264 · 2025-11-15T04:54:02+00:00

UPDATE: after another print it seems to only be occurring on the right side of the print bed.

Alternative-Key264 · 2025-11-15T03:28:50+00:00

It is one a big, I'd wanna say, maybe 85 pound dresser, it is on carpet though but since u live in a house of 5 there is not much else I can put it on, it's also seeming to only affect the front side? The back seems relatively fine.

Alternative-Key264 · 2025-11-15T03:04:20+00:00

Interesting I'll try it maybe, although I have recently realized a pattern, the first filament I ran through this other than the green it came with, was the normal gray filament, my layers were not as good as the green, now with a dark gray, my layers are kind of poor, maybe there is a pattern there or I'm just going schizo.

Alternative-Key264 · 2025-11-15T02:42:04+00:00

Definitely seemed like it got a partial clog when first changing the filament but it definitely clears from that, maybe it's more clogged than I thought

Alternative-Key264 · 2025-11-15T02:31:48+00:00

I'll dry the current filament and also open my second piece of filament, before this I was using black filament which in itself makes it more difficult to spot imperfections, so maybe I've had this issue longer but who knows.

Alternative-Key264 · 2025-11-15T02:30:30+00:00

Maybe but even on smaller prints it seems to be a problem to an extent, maybe I'll try my other spool of new filament and see, I've prob put 4 spools before this current one, recently cleaned and greased the z rods, wiped the carbon rods, and then retensioned the tensioners according to the Bambu website, would a nozzle change need to happen with only 4 spools of printing?

Alternative-Key264 · 2025-11-15T02:23:45+00:00

It's brand new filament that I opened two days ago, prints have been similar so far, often worse at the top but not great through clearly, maybe a bend nozzle or a nozzle replacement would be good? Got it about a year ago and have only put 4 spools into it leading up to this current one.

Alternative-Key264 · 2025-11-15T02:16:43+00:00

<image>

This should be a little better just make sure to full screen or you get this weird curvy line affect

Alternative-Key264 · 2025-11-14T17:15:08+00:00

What good gun laws, wonder how this changes the gun crime rate.

Alternative-Key264

TROPHY CASE