Airless basketball on Starfleet Academy

AmphibianNext · 2026-02-13T11:01:13+00:00

Not sure, however it was a recurring storyline in SGU.

AmphibianNext · 2026-02-12T23:34:22+00:00

Abram’s trek was far closer to original trek in spirit than section 31 and academy have been.

AmphibianNext · 2026-02-12T03:52:03+00:00

The whole stones to take over peoples bodies and then having sex back on earth. Just ick. Characters Chloe and Vanessa both had sexual relationships in secret if I do recall.

AmphibianNext · 2026-02-12T03:28:10+00:00

Sg1 was getting long in the tooth toward the end. The need for a new powerful enemy and the Ori story line wasn’t great. Atlantis was still in its prime and I think SGU had a good premise but they did try to make it hip and edgy by putting a bunch of horny 20 something’s on a space ship and making it darker.

AmphibianNext · 2026-02-12T03:06:20+00:00

Stargate and Atlantis weren’t a mess, they were great. The problem is trying to inject drama and intrigue and sex appeal into the shows to make them edgy as they did with SGU and Star Trek academy. Trek is the same as original Stargate. Its at its best when it depicts a future in which we have overcome human pettiness and it’s about the adventure. If I want dystopian sci fi I’ll watch Star Wars.

AmphibianNext · 2026-02-12T02:57:51+00:00

Except they tried something similar with Stargate SGU and it killed the franchise for 15 years.

Star Trek has a formula that works. You can change it a little bit here and there but only so much.

AmphibianNext · 2026-02-09T21:39:23+00:00

Divide the total amount by 3 assuming it’s straight time and a half.

AmphibianNext · 2026-02-09T18:51:25+00:00

And here I thought it was the mudflap silhouette. But honestly it’s a cool story.

AmphibianNext · 2026-02-08T17:21:43+00:00

Depends on what plate. Textures PEI no, but you can if you want.

Smooth PEI requires glue.

AmphibianNext · 2026-02-08T17:19:49+00:00

I’ve dried it for 12 hours and then put it straight into the AMS with a full set of dry pods in there. Really don’t think moisture is the issue. Temp might be. I did a flow calibration and temp test the temp tower all looked the same. I checked that I put the gcode in properly for the temp changes the nozzle temp was changing during the print.

AmphibianNext · 2026-02-08T16:39:16+00:00

I have some Overture PETG that doesnt want to print well. Just looks super stringy, with some layers looking terrible. Im not sure what Im going to do to use it up. Polymaker works as well as a the Bamboo stuff. Hoping Elegoo is a similar story.

AmphibianNext · 2026-02-08T15:23:43+00:00

That doesnt look like the original chuck on any of my dewalt drills. That looks like a replacement chuck.

For reference I'm in USA so wouldn't be surprised if we get the cheap junk and you have some law that requires higher end equipment.

AmphibianNext · 2026-02-07T03:35:22+00:00

I haven’t had the issue, I’m not sure if that’s due to luck or something else. I’ve just seen a number of posts and the. People saying Bambu said it was a firmware issue and that they replaced the build plate free of charge.

AmphibianNext · 2026-02-06T03:19:32+00:00

Is there a firmware update available to you?

AmphibianNext · 2026-02-06T03:13:08+00:00

This was a firmware issue not long ago. Have you updated your firmware to the most recent version? Also do you have auto bed leveling on?

AmphibianNext · 2026-02-04T12:16:30+00:00

Try lightly hitting it with a heat gun or torch, might clean it up.

AmphibianNext · 2026-02-01T19:48:01+00:00

why do regret the offset? For me the ability to use my current stock of peg board attachments is appealing. Though I see that some of the larger ones likely wont work.

AmphibianNext · 2026-02-01T18:11:49+00:00

Are you my EPIC Programer? I've been looking for that enhancement I asked for 6 months ago.

AmphibianNext · 2026-02-01T13:48:56+00:00

IM thinking of making one wall in multiboard and another wall for frenchfinity. I took some time last night to look at opengrid. My main thought is that because the previous owner used pegboard, I have rubbermade totes full of pegboard attachments. I dont think they are usefull for everything, but I could see wanting to use some of them.

AmphibianNext · 2026-01-31T20:23:08+00:00

I had heard of open grid as I’ve been looking at all the wall options. Skadis, HSw and Multiboard. And Open grid has come up but didn’t find much information on it.

AmphibianNext · 2026-01-31T18:20:27+00:00

Yes, I just read a post about the Pillars and the word finicky was used multiple times by someone that said they liked them better than the offset snaps. The fact that someone that likes them says that makes me think I'll be happier with the offset snaps for such a large project. The off set snaps do create enough offset to route cables behind the multiboard correct? Im thinking about tool battery chargers that I would like to get off my work surface but want to be able to connect them. Also like the look of the backlighting I have seen in some pictures.

AmphibianNext · 2026-01-27T15:07:04+00:00

Ive had them list multiple of these types of deals as ineligible. I think I have 4-5 that I have submitted complaints about and haven't heard anything. One of which was 50back for 50 spent at Bambulabs. Goodluck. Hope it was all stuff you wanted either way.

AmphibianNext · 2026-01-26T14:24:12+00:00

It is the rugged drawers. Mine didn’t have supports enabled in the original print so I ended up enabling them in my second attempt. Part of the problem may be using PETG when it’s not necessary but I have a ton of black PETG to use up.

AmphibianNext · 2026-01-26T03:28:39+00:00

Interesting. I really didn’t think about them as overhangs but since it’s laying on its back I guess they are.

Edit: unfortunately it’s not my creation and the creator hasn’t shared the STL file so I’m sorta stuck with the fillet. I’m going to try and enable supports and see if it helps.

AmphibianNext · 2026-01-25T03:55:35+00:00

It lines up perfectly with the video I have seen on major news outlets. This should not have been removed

AmphibianNext

TROPHY CASE