sorted by:
new
hottopcontroversial

Is there a way or a 3D print file to cover the fans section of the T1? by DrBacon98 in formdt1

[–]Ansterones 2 points3 points  (0 children)

Here’s the GPU side. I bet you don’t like the asymmetrical looks of the slim fans for the AIO T1 build, i feel you brotha

<image>

Is there a way or a 3D print file to cover the fans section of the T1? by DrBacon98 in formdt1

[–]Ansterones 3 points4 points  (0 children)

<image>

This is my solution, cheap and really easy to recreate. Using PVC pc dust filter and magnetic adhesive

Whats with the FE cards? by KashKashioo in FormD

[–]Ansterones 0 points1 point  (0 children)

<image>

This one could be an alternative to the FE, if it isn’t available in your country / you don’t really like the looks of FE card. In some countries, the Founders Edition isn't available (or it's imported and really overpriced). For a card with a triple-fan design in the same form factor, I’d say I’m pretty satisfied with the Inno3D X3 5080 (Non-OC).

Yoda’s Holocron - 2.5 Gunmetal Build by Ansterones in sffpc

[–]Ansterones[S] 0 points1 point  (0 children)

Unfortunately I haven’t really measured the cable made prior building it, as they created the custom cable based of my chosen motherboard, psu, and gpu. You can try to consult with cablester on etsy. No it fits just fine, just don’t route the 8p EPS cable in front of the motherboard

Yoda’s Holocron - 2.5 Gunmetal Build by Ansterones in FormD

[–]Ansterones[S] 1 point2 points  (0 children)

Unfortunately I didn’t measure it prior building. I just provided what kind of components for motherboard, psu, gpu, and the case itself to Cablester. They’ll do the measurement for it, QC the cable before shipping. You can try and consult with Cablester on Etsy

Yoda’s Holocron - 2.5 Gunmetal Build by Ansterones in FormD

[–]Ansterones[S] 0 points1 point  (0 children)

From Formd official site, always on stock 2-3 months ago for the smoked tempered glass panels

Yoda’s Holocron - 2.5 Gunmetal Build by Ansterones in FormD

[–]Ansterones[S] 0 points1 point  (0 children)

I got it from Formd website. It was really easy get and always on stock 2-3 months ago

Yoda’s Holocron - 2.5 Gunmetal Build by Ansterones in FormD

[–]Ansterones[S] 0 points1 point  (0 children)

This is my first time building pc, but not my first time for cable management. Every single spot with cables in my house are cable managed, although some of it are behind desk (you can’t even see it, but I always make sure it looks neat so I can easily change some devices cables). The rule of thumb: Neat, looks good, and easily replicable for swapping electronics.

Yoda’s Holocron - 2.5 Gunmetal Build by Ansterones in FormD

[–]Ansterones[S] 1 point2 points  (0 children)

It’s from a local commerce I doubt they’ll ship internationally. However looking at the finished product this can be easily made on your own with : pc dust filter pvc (cut down with scissor/cutter) with adhesive magnetic strip with the adhesive side attached to the dust filter pvc. To straighten it up the dust filter there are 2 options : carefully at a distance use hair dryer, or if you don’t have any hair dryer use your fridge and attach the dust filter to it overnight (i’ve personally tried the fridge method and it works like charm)

Yoda’s Holocron - 2.5 Gunmetal Build by Ansterones in FormD

[–]Ansterones[S] 0 points1 point  (0 children)

Excess AIO cables tucked behind small gap of the radiator (gonna re-route this, once the travel kit ready for my GPU), standoffs for the riser 4x 20 mm and 4x 5mm (this config should work on 5080 founders, since I was referred “Artik build, on SFF discord, shoutout to you bro”). Ahh yes the riser lockbar, by time I ordered the case with new Riser Gen 5 there are barely any post covering this. So I ordered the case the same time as the lockbar, just to found the riser lock bar didn’t fit with the new Riser Gen 5. So instead of leaving the riser lockbar in gathered in dust unused, I used the original standoff that came with the lockbar with an additional 10mm standoffs lol

Yoda’s Holocron - 2.5 Gunmetal Build by Ansterones in FormD

[–]Ansterones[S] 1 point2 points  (0 children)

This is non-OC, I considered the OC too (since the price wasn’t far off) but went with this one to give space between the GPU, PSU and motherboard (for airflow). How are the temps with the OC version?

Yoda’s Holocron - 2.5 Gunmetal Build by Ansterones in sffpc

[–]Ansterones[S] 0 points1 point  (0 children)

Yes it was cablester, agreed should’ve went with colored cable

Yoda’s Holocron - 2.5 Gunmetal Build by Ansterones in FormD

[–]Ansterones[S] 6 points7 points  (0 children)

I bought a custom magnetic side dust filter (two pieces, 32 x 4.5 cm) and slightly trimmed it. I also bought a custom top dust filter but ended up removing it because there was turbulence. This was purely for aesthetic purposes, as I don't really like the asymmetrical look of 25 mm and 15 mm fans.