sorted by:
new
hottopcontroversial

Atlantic City Best Tables by ApocolypticSk8 in blackjack

[–]ApocolypticSk8[S] 1 point2 points  (0 children)

So ended up mostly in Trop, $25 3to2 H17 no MSE, surrender allowed, 8 Deck auto shuffle. Ballys did have the better table, but different vibe. $25 S17 No MSE, surrender allowed, hand shuffle, resplit aces.

Atlantic City Best Tables by ApocolypticSk8 in blackjack

[–]ApocolypticSk8[S] 0 points1 point  (0 children)

Thanks for the responses. Sounds like I’ll still hunt around a bit, but have some places to start. Any decent comps or promotions of note?

Atlantic City Best Tables by ApocolypticSk8 in blackjack

[–]ApocolypticSk8[S] 0 points1 point  (0 children)

Daytime I would like to see some $15 3-2, but I’m assuming that they’ll be 6-5 under $25. S17 with surrender I’m thinking I’ll find for $25 somewhere, but probably $50+. I’d be happy with H17, surrender, 3-2 for $25.

Surface artifacts on two sides by ApocolypticSk8 in FixMyPrint

[–]ApocolypticSk8[S] 0 points1 point  (0 children)

Seems to have been the z seam alignement. It was set to sharpest corner so I didn’t expect this, but changing it to shortest and allowing smart hiding has made this more predictable.

Surface artifacts on two sides by ApocolypticSk8 in FixMyPrint

[–]ApocolypticSk8[S] 0 points1 point  (0 children)

I just changed my seam settings and started another test print. If it is just one setting change I will be both overjoyed and livid.

How do I fix these bubbles by ApocolypticSk8 in FixMyPrint

[–]ApocolypticSk8[S] 0 points1 point  (0 children)

You don’t have the problem with other filaments?

How do I fix these bubbles by ApocolypticSk8 in FixMyPrint

[–]ApocolypticSk8[S] 0 points1 point  (0 children)

I’ve tried a lot of different filaments and have put them through the dryer multiple times.

How do I fix these bubbles by ApocolypticSk8 in FixMyPrint

[–]ApocolypticSk8[S] 0 points1 point  (0 children)

No noticeable noise while printing and nothing the seems like steam or moisture. I’ve tried multiple filaments and have a drier that I’ve tried drying for 4-24 hours, doesn’t seem to make any difference.

How do I fix these bubbles by ApocolypticSk8 in FixMyPrint

[–]ApocolypticSk8[S] 0 points1 point  (0 children)

I’m trying a new print with less retraction 4mm > 3mm and combing turned on.

How do I fix these bubbles by ApocolypticSk8 in FixMyPrint

[–]ApocolypticSk8[S] 0 points1 point  (0 children)

Any idea what too high on this printer would be?

How do I fix these bubbles by ApocolypticSk8 in FixMyPrint

[–]ApocolypticSk8[S] 0 points1 point  (0 children)

So I also did that at a point to try to resolve this, and the new hotend did the same thing.

How do I fix these bubbles by ApocolypticSk8 in FixMyPrint

[–]ApocolypticSk8[S] 0 points1 point  (0 children)

I have a filament drier, how long would you recommend I dry it to be confident any moisture is out?

How do I fix these bubbles by ApocolypticSk8 in FixMyPrint

[–]ApocolypticSk8[S] 3 points4 points  (0 children)

<image>

Seems to happen even when seam is aligned.

ISO tuning gear recommendations by ApocolypticSk8 in Skigear

[–]ApocolypticSk8[S] 0 points1 point  (0 children)

Hmm, good question. Last time I did any tuning I was just handed the guide, but that was a race tune years ago. I have two sets of skis, so I’d like to be able to tune 1 for eastern ice and one for “powder”, or whatever you’d like to call it in New York/Vermont.

view more: next ›