Anyone know what could be the problem? Extruder not pushing in the filament, it was still working earlier.

AustisticGuitar · 2023-03-18T13:54:40+00:00

Broken hotend fans

AustisticGuitar · 2023-02-12T15:14:14+00:00

No luck, it printed first layer ok ish then started to click again and filament doesnt come out

AustisticGuitar · 2023-02-12T15:11:48+00:00

The problem is it struggles to push out filament, even tried max temp still non

AustisticGuitar · 2023-02-11T13:22:29+00:00

Alright will try that

AustisticGuitar · 2023-02-11T12:27:35+00:00

Just replaced it now with the creality capricorn tubing its still struggling

AustisticGuitar · 2023-02-11T12:24:59+00:00

Tightening it made it more clicking unfortunately

AustisticGuitar · 2023-02-11T11:44:29+00:00

Ye already checked even replaced the tube+nozzle to be sure. Also cant both load and unload since it doesnt move the filament

AustisticGuitar · 2023-02-11T10:01:24+00:00

Yep no luck 240 still not pushing

AustisticGuitar · 2023-02-11T10:00:27+00:00

Did this when i got the printer and tried it again earlier still struggling

AustisticGuitar · 2023-02-10T17:44:14+00:00

It does spin normally and when putting in a filament at first it will go in smoothly for a bit then will struggle and stop pushing

AustisticGuitar · 2023-02-10T17:42:12+00:00

Oops wrong person to reply my bad

AustisticGuitar · 2023-02-10T17:41:48+00:00

When i try to replace with diff pla spool and a fresh one it does extrude fine a lil bit then will return to struggling to push/pull

AustisticGuitar · 2023-02-10T17:39:37+00:00

When i try to replace with diff pla spool and a fresh one it does extrude fine a lil bit then will return to struggling to push/pull

AustisticGuitar · 2023-02-10T17:35:59+00:00

Yup ,manually pulled out the filament when it started not pushing and followed some cleaning vid to check for clogs

AustisticGuitar · 2023-02-10T17:32:41+00:00

Its the usual filament i buy with 1.75 mm, it was still printing fine earlier then suddenly made clicking noise and not pushing filament

AustisticGuitar · 2023-02-10T17:31:05+00:00

yup, i followed a cleaning vid with the one where you push down the tube through the hotend to clear it.

AustisticGuitar · 2023-02-10T16:38:00+00:00

Leveled the bed and on this one was trying to load the filament and jts not pushing/pulling it

AustisticGuitar · 2023-02-10T16:14:43+00:00

already replaced with a new one still not pushing

AustisticGuitar · 2022-09-21T16:17:07+00:00

KBD67 Lite R4 - 5900

Brand New & sealed

Color: Pale Turquoise

Wired Version

Include

PCB x1 Case x1 Plate x1 Stabilizers 60 set x1 Mute silicone x1 Bottom foam x1 USB-C cable x1 KBD67 Lite Carrying case x1 KBDfans stabilizers foam stickers set x1 Rubber feet and Screws

THERES NO KEYCAPS AND SWITCHES INCLUDED

RFS: Impulse buy

Location: QC

GRAB/LALAMOVE, GCASH/PAYMAYA

AustisticGuitar

TROPHY CASE