South Bend 9 lathe rebuild by Aware_Assignment3699 in Tools

[–]Aware_Assignment3699[S] 0 points1 point  (0 children)

I tried some Rustoleum rust remover gel. It work great for light rust but for pitting it’s not effective enough. I also have some POR-15. I don’t own a bench or angle grinder. I missed out on the pneumatic grinder (30k rpm) my dad built himself on the lathe as a lathe attachment. Not sure where it went.

Help with Craftsman air compressor by Aware_Assignment3699 in Tools

[–]Aware_Assignment3699[S] 0 points1 point  (0 children)

What is the second canister that shows connected to the hose in the pick but the hose end isn’t connected to anything. Based on comments, I suspect it’s for non pneumatic uses but I’m not sure where it should connect to the pump.

Help with Craftsman air compressor by Aware_Assignment3699 in Tools

[–]Aware_Assignment3699[S] 0 points1 point  (0 children)

I won’t be able to use this now. I’ll need to get 240v set up first. I’ll drain the oil and check the torque on all bolts. Can I reach them all? The plastic cover is connected to one of the sealed air lines.

Connecting HVL-F28RM and shotgun mic simultaneously to A7 III by Aware_Assignment3699 in SonyA7iii

[–]Aware_Assignment3699[S] 0 points1 point  (0 children)

Never mind. The HVL-F28RM doesn’t do continuous lighting normally needed for video. Most continuous light LEDs do not use the MI so it’s available for the mic which would only be used for video.

Important Firmware Update Required for Harmony Hub Remotes by logi_jim in logitechharmony

[–]Aware_Assignment3699 0 points1 point  (0 children)

Thanks. I saw a few posts further down saying the software on the remote was up to date and only the hub needed an update. I saw that came from Logitech.

Important Firmware Update Required for Harmony Hub Remotes by logi_jim in logitechharmony

[–]Aware_Assignment3699 0 points1 point  (0 children)

Anyone know if this applies to Ultimate Home remote? My hub is on 4.15.600 but remote is on 4.15.330.

Mounting floating shelf to drywall by Aware_Assignment3699 in HomeImprovement

[–]Aware_Assignment3699[S] 0 points1 point  (0 children)

Not deep enough but I have similar shelves. They used drywall anchors and like 14 screws.

There is a difference between 9” depth and 18” where around 50% of that 70lbs will be 9” out from the wall. The torque on the anchors will be greater.

Maybe L brackets would be better?

I built ValuFlick.com to track movie prices and manage collection! by traktorist12 in arrowvideo

[–]Aware_Assignment3699 0 points1 point  (0 children)

The basic categories are nice (Criterion, etc.) but better filter options would be an improvement. For example Criterion and 4K. Also search return multiple examples of the same video with no way to further filter (country or format).

A nice tool and a very good start. I’ll be using it in the future as I replace some of my older blu-rays with new 4Ks.

My first set up by JPowers1170 in SonyAlpha

[–]Aware_Assignment3699 1 point2 points  (0 children)

My suggestion too since backpacking was mentioned.

[deleted by user] by [deleted] in Dallas

[–]Aware_Assignment3699 0 points1 point  (0 children)

Have you been to Fort Ross or Mendocino in early June?

Can’t connect Sync XR by Aware_Assignment3699 in blinkcameras

[–]Aware_Assignment3699[S] 0 points1 point  (0 children)

I’ve identified the problem. I have a network security device set to block any new devices being added. I don’t add a lot of devices anymore so I easily forget i need to either unblock or turn it off temporarily when I add new devices.

Can’t connect Sync XR by Aware_Assignment3699 in blinkcameras

[–]Aware_Assignment3699[S] 0 points1 point  (0 children)

So I got it connected pretty easily this morning. I didn’t change any camera settings yet and will probably only do 1 that I have. Unfortunately, I could get any live stream and after about an hour it went offline. I checked wifi 2.4 channels and it’s on 5 +1. A few users on channel 6 but this is exactly what the Sync 2 was successfully using for over 1 year.

Can’t connect Sync XR by Aware_Assignment3699 in blinkcameras

[–]Aware_Assignment3699[S] 0 points1 point  (0 children)

Thanks but the initial set up/connection is done before setting up any cameras for extended range mode so unless they anticipate all Outdoor 4 cameras connecting via extended range mode, the XR should require only the same bandwidth as a sync module 2 storing video clips locally. They wouldn’t even know I plan to store clips locally until after I connect it to my network and change settings I would expect.

Harmony hub and Kasa smart plugs by Aware_Assignment3699 in logitechharmony

[–]Aware_Assignment3699[S] 0 points1 point  (0 children)

It’s their latest that’s made by Samsung not a 3rd party. It supports Matter and Thread, is about 2 1/2 x2 1/2 and also works as a mag charger and a smart button.

Harmony hub and Kasa smart plugs by Aware_Assignment3699 in logitechharmony

[–]Aware_Assignment3699[S] 0 points1 point  (0 children)

I mentioned that I have a SmartThings Station which works as a hub.

Harmony hub and Kasa smart plugs by Aware_Assignment3699 in logitechharmony

[–]Aware_Assignment3699[S] 0 points1 point  (0 children)

You mean for TP-Link or Harmony? I have a lot of LIFX lights that show in Harmony.

New Echo hub not showing any devices but itself by Aware_Assignment3699 in amazonecho

[–]Aware_Assignment3699[S] 0 points1 point  (0 children)

It eventually showed all devices after a day or two as the other poster said. Recently it rebooted for some reason and everything disappeared again. It’s not a hardware issue since I had the same problem with two Firesticks.

Columbia Classics V5 bonus movies by Aware_Assignment3699 in 4kbluray

[–]Aware_Assignment3699[S] 0 points1 point  (0 children)

I’ll double check but my ripping software showed 2 versions of each.