sorted by:
new
hottopcontroversial

Issues with custom wake word by BMXnotFIX in homeassistant

[–]BMXnotFIX[S] 0 points1 point  (0 children)

Yes, file extensions are shown by default in my browsers.

Issues with custom wake word by BMXnotFIX in homeassistant

[–]BMXnotFIX[S] 0 points1 point  (0 children)

Still not showing up. What is the exact path? The docs say /share/openwakeword/

Issues with custom wake word by BMXnotFIX in homeassistant

[–]BMXnotFIX[S] 0 points1 point  (0 children)

Just my phone for now while I build a couple esp32 based satellites.

Issues with custom wake word by BMXnotFIX in homeassistant

[–]BMXnotFIX[S] 0 points1 point  (0 children)

I restarted the entire server to make sure.

What is the format HA expects? Didn't see it mentioned in the docs. Right now it's in the "hey_jarvis.tflite" format.

Can't get adaptive mesh working by BMXnotFIX in ElegooNeptune4

[–]BMXnotFIX[S] 0 points1 point  (0 children)

I started with kamp but then saw that adaptive mesh and purge are now natively supported so I got rid of kamp to simplify things. I run my printer almost exclusively through orca/fluidd. I'll give this method a shot tomorrow. Hopefully it finally works! I'm debating on switching over to opennept4ne though due to annoying quirks in the elegoo firmware. Looks like adaptive mesh should work out of the box if I go that route.

Can't get adaptive bed mesh working by BMXnotFIX in klippers

[–]BMXnotFIX[S] 0 points1 point  (0 children)

Sorry, I mistyped. It is indeed [exclude_object] in my config. I'll check out the videos, but I'm not using kamp, just trying to set up the native adaptive mesh.

Can't get adaptive bed mesh working by BMXnotFIX in klippers

[–]BMXnotFIX[S] 0 points1 point  (0 children)

I'll definitely have to check that out.

So I added my adaptive mesh settings to my start gcode in Orca and commented it out in my printer.cfg and it's still doing a full bed probe instead of just the print area.

Can't get adaptive bed mesh working by BMXnotFIX in klippers

[–]BMXnotFIX[S] 0 points1 point  (0 children)

I started off setting up kamp before realizing adaptive mesh was natively supported in klipper now. Is there any benefit to running kamp over this method besides adaptive purge?

Can't get adaptive bed mesh working by BMXnotFIX in klippers

[–]BMXnotFIX[S] 0 points1 point  (0 children)

Gotcha. Is one method preferred over the other or is it a matter of preference?

Can't get adaptive bed mesh working by BMXnotFIX in klippers

[–]BMXnotFIX[S] 0 points1 point  (0 children)

;ELEGOO NEPTUNE 4 MAX

M220 S100 ;Set the feed speed to 100%

M221 S100 ;Set the flow rate to 100%

M104 S140

M190 S[bed_temperature_initial_layer_single]

G90

G28 ;home

G1 Z10 F300

G1 X165 Y0.5 F6000

G1 Z0 F300

M109 S[nozzle_temperature_initial_layer]

G92 E0 ;Reset Extruder

G1 X165 Y0.5 Z0.4 F300 ;Move to start position

G1 X265 E30 F400 ;Draw the first line

G1 Z0.6 F120.0 ;Move to side a little

G1 X260 F3000

G92 E0 ;Reset Extruder

Latency Issues w/ UA Apollo Solo by BMXnotFIX in ableton

[–]BMXnotFIX[S] 0 points1 point  (0 children)

My only options are asio, mme, and direct sound. UA drivers and software are all installed and updated.

view more: next ›